Why An Inline Filter Is A Good Idea.

If you are using a Water/Methanol Injection System it may greatly increase pump life to use a water/methanol filter. The AEM Water/Methanol Injection Filter prevents foreign particles as small as 40 microns from clogging or damaging pumps, injection nozzles check valves or flow sensors. The AEM Water/Methanol Injection Filter uses fittings for use with 1/4″ OD nylon tubing, so it fits most Water/Methanol injection kits on the market today!

• Simple to install, takes less than a minute!
• Fits virtually every Water/Methanol system on the market.
• Polypropylene housing – rugged material that is compatible with high concentrations of methanol.
• Completely Serviceable Assembly – can be disassembled, cleaned and reused for a long service life.
• Stainless Steel mesh strainer – AEMs custom mesh strainer filters down to 40 microns – MUCH smaller than similar filters.
• Large Filtering Area assure long service life and does not significantly reduce flow.
• Micronic Mesh Screen out-performs sintered filters in both filtering and serviceability.

AEM PART NUMBER – 30-3003

Please select your desired tank size from the drop down menu before adding your selection to the shopping cart

Water/methanol injection for gas engines is a proven means for effectively reducing engine inlet air temperatures and suppressing harmful detonation on forced induction and high performance naturally aspirated race engines. This allows racers to reliably increase boost and advance ignition timing—without using high-octane racing fuel—for power gains of up to 20%. AEM’s Water/Methanol Injection Systems utilize the most robust hardware combined with more advanced features than any other comparably priced water/methanol system.

The on-demand progressive controller in AEM’s Boost Dependent PN30-3300 Water/Methanol Injection kit bases injection flow on manifold pressure using an on-board MAP sensor (up to 35 PSI of boost) to ensure the proper amount of water/methanol injection at all points along an engine’s power curve.

AEM’s engineers spent extensive time developing the controller’s flow control strategy for a more linear flow output delivery. This means that the flow delivery better matches an engine’s need for water/methanol injection, which further optimizes charge air cooling and detonation control.

The new controller design features large, turn-resistant knobs and larger numbering to easily set accurate start and full activation points, with covered status LED and test buttons for added splash resistance. A plug is integrated into the controller housing for mating to the redesigned wiring harness’s positive-lock connector. The Boost Dependent controller housing has a molded-in, barbed nipple to accept a boost hose and a wiring legend on the back, integrated fuse and molded mounting tabs.

AEM’s Boost Dependent Water/Methanol Injection kit’s wiring harness is terminated with a positive-lock connector on one end and has color-coded wires to ease installation. Both the power and ground wires for the pump are included in the harness which simplifies the wiring process and eliminates any chance of the pump accidentally activating from a short in the system. An additional wire is included for adding an optional on/off solenoid to stop fluid flow when the system is inactive.

AEM’s Boost Dependent, PN 30-3300 gasoline Water/Methanol Injection System’s compact 1 gallon tank includes a high tech conductive low fluid level indicator with a positive lock connector and color matched wires to the wiring harness.

AEM strongly recommends that users never exceed a 50% methanol concentration when using any AEM Water Methanol system or component.

All AEM Water/Methanol injection systems and components (pump, lines, fittings, filter, flow sensor, tank, and nozzles) are 100% chemically compatible with methanol. However, for safety reasons we strongly recommend that users never use more than a 50% methanol concentration in our systems.

Methanol is a toxic and highly flammable chemical. 100% Methanol ignites easily and burns vigorously with an almost undetectable flame. Methanol can be absorbed through the skin and even small amounts can cause blindness or even death. Using this fluid at high pressures, without dilution, in an under-hood environment with nylon lines and push-to-connect fittings is very unsafe. The performance advantages of using greater than 50% methanol concentrations are small, if they exist at all. However, the safety issues are very real and far outweigh any perceived benefit of running high concentrations of methanol.

AEM Part Numbers
V2 Water Methanol Kit With 4 Liter Tank – 30-3300
V2 Water Methanol Kit With 19 Liter Tank – 30-3301

Water/methanol injection for gas engines is a proven means for effectively reducing engine inlet air temperatures and suppressing harmful detonation on forced induction and high compression naturally aspirated (NA) race engines. This allows racers to reliably increase boost and advance ignition timing—without using high-octane racing fuel—for power gains of up to 20%. AEM’s Water/Methanol Injection Systems utilize the most robust hardware combined with more advanced features than any other comparably priced water/methanol system.

The on-demand progressive controller in AEM’s Boost Dependent PN30-3302 tank-less Water/Methanol Injection kit bases injection flow on manifold pressure using an on-board MAP sensor (up to 35 PSI of boost) to ensure the proper amount of water/methanol injection at all points along an engine’s power curve.

AEM’s engineers spent extensive time developing the controller’s flow control strategy for a more linear flow output delivery. This means that the flow delivery better matches an engine’s need for water/methanol injection, which further optimizes charge air cooling and detonation control.

The new controller design features large, turn-resistant knobs and larger numbering to easily set accurate start and full activation points, with covered status LED and test buttons for added splash resistance. A plug is integrated into the controller housing for mating to the redesigned wiring harness’s positive-lock connector. The Boost Dependent controller housing has a molded-in, barbed nipple to accept a boost hose and a wiring legend on the back, integrated fuse and molded mounting tabs.

AEM’s Boost Dependent Water/Methanol Injection kit’s wiring harness is terminated with a positive-lock connector on one end and has color-coded wires to ease installation. Both the power and ground wires for the pump are included in the harness which simplifies the wiring process and eliminates any chance of the pump accidentally activating from a short in the system. An additional wire is included for adding an optional on/off solenoid to stop fluid flow when the system is inactive.

AEM strongly recommends that users never exceed a 50% methanol concentration when using any AEM Water Methanol system or component.

All AEM Water/Methanol injection systems and components (pump, lines, fittings, filter, flow sensor, tank, and nozzles) are 100% chemically compatible with methanol. However, for safety reasons we strongly recommend that users never use more than a 50% methanol concentration in our systems.

Methanol is a toxic and highly flammable chemical. 100% Methanol ignites easily and burns vigorously with an almost undetectable flame. Methanol can be absorbed through the skin and even small amounts can cause blindness or even death. Using this fluid at high pressures, without dilution, in an under-hood environment with nylon lines and push-to-connect fittings is very unsafe. The performance advantages of using greater than 50% methanol concentrations are small, if they exist at all. However, the safety issues are very real and far outweigh any perceived benefit of running high concentrations of methanol.

AEM PART NUMBER 30-3302

AEM Part Number 30-5142

WHAT IT DOES

If you are using a Water/Methanol Injection System and want to know exactly how much fluid you are actually injecting into your engine, the AEM Water/Methanol Flow Gauge is a must. It replaces the “dummy light” with actual data displayed on a smooth moving needle-type gauge that allows you to accurately monitor the status of your injection system in real time. The AEM Water/Methanol Flow Gauge comes with black and silver bezels and white and black faceplates for multiple color combinations.

The gauge kit includes a precision flow sensor and fittings for use with 1/4″ OD nylon tubing, so the AEM Water/Methanol Flow Gauge fits most Water/Methanol injection kits on the market today.

For best results the 0-1000CC Flow Gauge (AEM part# 30-5142) should be used on Water/Methanol kits injecting more than 500 cc/min and is ideal for those with the AEM Water/Methanol kit using the largest size or multiple sized nozzles. If you are using only a small or medium AEM nozzle, we suggest the 0-500CC Flow Gauge (AEM part# 30-5141)

WHY YOU WANT ONE

AEM’s Water/Methanol Gauge gives you the exact amount of water/methanol you are spraying into your engine. Boost with the extra confidence of knowing your flow though your entire RPM and boost range. The gauge comes with both a white and black face place to perfectly match your interior.

PRODUCT FEATURES

• Gauge Readout from 0 to 1000cc
• Adjustable backlighting via a dial on the back of the gauge
• Includes black and silver interchangeable bezels and white and black faceplates
• 320 degree viewing area for unsurpassed resolution
• Fits virtually every water/methanol kit on the market today!
• 0-5v analog output included for use with data loggers and virtually any engine management system

Special Order Item Only.

From the selection on the drop down box below we offer the popular Racing Beat-modified High Performance Holley Intake System Kit for the 1974-1985 12A & 13B with stock port, street port and bridge port engines.

One of most significant benefits of this complete ready-to-go kit is that is takes all the guesswork, trial-and-error, and frustration out of attempting to assembly your own intake kit! We’ve taken over 40 years of our rotary engine experience and know-how and combined it for you in this complete, ready-to-install kit. Our intake kits has been thoroughly developed and tested using our in-house engine dyno to ensure maximum performance for each specific engine application.

The heart of each intake system is a performance-proven Holley carburetor. Depending on the requirements of each specific application, the carburetor is disassembled by Racing Beat’s carburetor technicians then reworked, retuned, and reconfigured specifically for use with a designated rotary engine application. This process is not a simple “re-jetting” project, but a complex series of steps requiring machining, drilling and reconfiguring of the main and metering bodies, adjustment of the float bowls, and complete replacement of all jets.

Headers must be used with these street port intake systems to achieve maximum horsepower gains.

The carburetors and manifolds used in these Holley kits are also available separately in the “Holley Components” section. Also see the “Intake” section for other related intake components.

Note: Installation of this kit requires use of a high performance fuel pump delivering 6 psi @ 20 gph.

PLEASE SELECT YOUR CORRECT MODEL APPLICATION FROM THE DROP DOWN MENU NET TO THE “ADD TO CART” BUTTON

Please Note that this item is special order only, and is subject to our non return policy for special order items under our T&C’s of sale. for more information please check out T&C’s here

RE-Amemiya boasts a increase in response at higher revs in the FC3S due to their Dual-Entry Air filter intake design. The RE-Amemiya Response Cleaner Air Filter System will be a complete bolt-on kit and is an easy and clean way to increase both response and power for your FC3S.

Special Order only so please allow 2-6 weeks for delivery.

The all new ribbed main body dissipates heat more effectively and the venturi shaped funnel creates a sharp dynamic sound.
Venturi Drive dump valves also feature “Dual Drive” for maximum response, a small port for low boost and a larger port for high boost.

The main purpose of the dump valves is to improve the response of the turbo by quickly releasing the boost pressure before the turbo stalls.

They are made from die cast polished aluminium with a brass piston and a rubber diaphragm, meaning they can easily cope with boost pressures up to 1.2 bar with the supplied spring.
There is an alternative hard spring for boost pressures above 1.2bar and also a soft spring available for very low boost applications.

Blitz VDSS Blow Off Valves  are also tension adjustable.

This kit includes everything needed to install onto your vehicle. (Please remember that most of these kits are designed to install on a standard setups so if you intend to install this on a single turbo conversion some modification may be required)

This kit is a Release Type

Please allow up to 28 days for delivery for this item if not in stock.

Universal Kit includes

• SQV Blow Off Valve
• O-ring,
• C-ring (Securing Clip)
•  Vacuum Hose T-fitting 6×4×6
• Vacuum Hose T-fitting 4×4×4
• Inline Air Filter and Tylap.
  

HKS Part Number: 71008-AK001

Please Allow up to 28 days for delivery for delivery.

The Power Intake incorporates a newly developed material (layer filter of dry density fibers) which improves the element density. This allows maximum protection from foreign materials entering the engine. Compared with past model, the Power Intake has also succeeded in decreasing its ventilation resistance by about 10% (pressure loss) for maximum performance and protection. The Power Intake is dry-type filter and is trouble free. Some of the problems associated with wet type cleaners, such as oil sticking to the air flow meter, are a thing of the past. The Power Intake is basically maintenance free. Filter replacement, when necessary, can be done at a very low cost.

CONCEPT:

• Air filter with minimal air-flow restriction

CHARACTERISTICS:

• Dual funnel filter system minimizes intake turbulence