REMEMBER TO CHOOSE THE CORRECT SHIPPING OPTION BEFORE ADDING ITEMS TO THE CART!

High Flow Air Filter for RX-7 FB by K&N

High Flow Air Filter for RX-7 FB by K&N

K&N’s replacement air filters are designed to increase horsepower and acceleration while providing excellent filtration. We make over 1,20 ...

£ 46.99
add to cart
show details
K&N’s replacement air filters are designed to increase horsepower and acceleration while providing excellent filtration. We make over 1,200 different replacement air filters for virtually every vehicle on the road. These filters are washable and reusable and are custom designed to fit into your existing factory air box.

Their drop-in design means adding performance is simple. With most vehicles you simply remove the disposable air filter and replace it with a K&N. See applicable instruction sheet for details. Our stock replacement air filters for street vehicles are covered by our famous K&N Million-Mile Limited Warranty™ and will be
Racing Beat Air Cleaner Assembly for 71-85 Rotary Engines inc  RX-7 FB

Racing Beat Air Cleaner Assembly for 71-85 Rotary Engines inc RX-7 FB

Racing Beat's dyno-proven Power Pulse Air Filter Assembly, for all 1971-85 Stock Carburettor Bodies, is designed specifically for performanc ...

£ 139.99
add to cart
show details
Racing Beat's dyno-proven Power Pulse Air Filter Assembly, for all 1971-85 Stock Carburettor Bodies, is designed specifically for performance. While the assembly uses the same Racing Beat foam air filter element that fits the stock canister, the design of the Power Pulse canister both improves air flow into the carburettor and limits the introduction of dirt particles into the filter element.

The spun aluminium canister pieces are powder-coated white for added durability. There is no provision for emission control valve hose/air pump hose connections on this assembly; however, there is a position available to connect a crankcase breather tube if needed.

The Racing Beat-designed Foam Air Filter Element for all 1971-85 Rotaries consists of a polyurethane foam over a metal screen form that interchanges exactly with the stock element. The foam element can be re-used by periodically cleaning in solvent and re-oiling.

While the element offers no significant increase in air flow when compared to a clean, stock paper element, as the paper element collects dirt its air flow capacity decreases dramatically while the foam element is nearly unaffected.

Please Note that this item is special order only, and is subject to our non return policy for special order items under our T&C's of sale. for more information please check out T&C's here
Racing Beat Modified Holley Intake Kit 76-85 12A Stock Port

Racing Beat Modified Holley Intake Kit 76-85 12A Stock Port

We offer the extremely popular Racing Beat-modified High Performance Holley Intake System Kit for 1976-1985 12A Stock (non-ported) engines.< ...

£ 949.00
add to cart
show details
We offer the extremely popular Racing Beat-modified High Performance Holley Intake System Kit for 1976-1985 12A Stock (non-ported) engines.

Racing Beat's High Performance Holley Intake System Kit has proven over the years to be an extremely reliable carburetor upgrade, with very "streetable" engine smoothness and drivability characteristics. Fuel economy is comparable to the stock carburetor under similar driving conditions.

Complete Ready-to-Install Kit
One of most significant benefits of this complete ready-to-go kit is that is takes all the guesswork, trial-and-error, and frustration out of attempting to assembly your own intake kit! We've taken over 40 years of our rotary engine experience and know-how and combined it for you in this complete, ready-to-install kit. Our intake kits has been thoroughly developed and tested using our in-house engine dyno to ensure maximum performance for each specific engine application.

Rotary-tuned By Racing Beat
The heart of each intake system is a performance-proven 4-barrel Holley carburetor. Depending on the requirements of each specific application, the carburetor is disassembled by Racing Beat's carburetor technicians then reworked, retuned, and reconfigured specifically for use with a designated rotary engine application. This process is not a simple "re-jetting" project, but a complex series of steps requiring machining, drilling and reconfiguring of the main and metering bodies, adjustment of the float bowls, and complete replacement of all jets. Each application has been fully developed and tested on our in-house dyno facility to ensure maximum performance.

Each comprehensive package includes a Racing Beat cast-aluminum high-rise intake manifold with a vacuum source for power brakes, a Racing Beat-modified Holley carburetor (465 CFM), foam air cleaner and canister assembly, throttle and metering oil pump linkages, and appropriate gaskets. All emissions control fittings are eliminated. This carburetor includes a vacuum-operated choke.

Performance
When installed on a 1976-78 RX-3 or a 1979-85 RX-7 12A engine, this kit increases engine output by approximately 20 HP with the stock exhaust system. However, for increased performance gains we strongly recommend the installation of an exhaust header/presilencer/Power Pulse Muffler combo (10+ HP) or an open exhaust (15+ HP) - resulting in total performance gains of between 30-35 HP depending on your specific intake/exhaust configuration..

The carburetors and manifolds used in these Holley kits are also available separately in the "Holley Components" section.

Note: Installation of this kit requires use of a high delivery fuel pump kit delivering 6 psi @ 20 gph.

Please Note that this item is special order only, and is subject to our non return policy for special order items under our T&C's of sale. for more information please check out T&C's here
Racing Beat Modified Holley Intake Kit 74-85 12A / 13B

Racing Beat Modified Holley Intake Kit 74-85 12A / 13B

PLEASE SELECT YOUR CORRECT MODEL APPLICATION FROM THE DROP DOWN MENU NET TO THE "ADD TO CART" BUTTON
£ 990.00

add to cart
show details
PLEASE SELECT YOUR CORRECT MODEL APPLICATION FROM THE DROP DOWN MENU NET TO THE "ADD TO CART" BUTTON

From the selection on the drop down box below we offer the popular Racing Beat-modified High Performance Holley Intake System Kit for the 1974-1985 12A & 13B with stock port, street port and bridge port engines.

One of most significant benefits of this complete ready-to-go kit is that is takes all the guesswork, trial-and-error, and frustration out of attempting to assembly your own intake kit! We've taken over 40 years of our rotary engine experience and know-how and combined it for you in this complete, ready-to-install kit. Our intake kits has been thoroughly developed and tested using our in-house engine dyno to ensure maximum performance for each specific engine application.

The heart of each intake system is a performance-proven Holley carburetor. Depending on the requirements of each specific application, the carburetor is disassembled by Racing Beat's carburetor technicians then reworked, retuned, and reconfigured specifically for use with a designated rotary engine application. This process is not a simple "re-jetting" project, but a complex series of steps requiring machining, drilling and reconfiguring of the main and metering bodies, adjustment of the float bowls, and complete replacement of all jets.

RacingBeatHolleyIntakeKit76-85StreetPort500px Headers must be used with these street port intake systems to achieve maximum horsepower gains.

The carburetors and manifolds used in these Holley kits are also available separately in the "Holley Components" section. Also see the "Intake" section for other related intake components.

Note: Installation of this kit requires use of a high performance fuel pump delivering 6 psi @ 20 gph.

PLEASE SELECT YOUR CORRECT MODEL APPLICATION FROM THE DROP DOWN MENU NET TO THE "ADD TO CART" BUTTON

Please Note that this item is special order only, and is subject to our non return policy for special order items under our T&C's of sale. for more information please check out T&C's here
AEM V2 Water/Methanol Injection Kit (Turbo/FI Applications) NO TANK KIT

AEM V2 Water/Methanol Injection Kit (Turbo/FI Applications) NO TANK KIT

Reduce Intake Air Temperatures and Exhaust Gas Temps, while  Increasing Octane Rating of Pump Fuel, Knock Protection. Run More Boost and Ti ...

£ 349.99
add to cart
show details
Reduce Intake Air Temperatures and Exhaust Gas Temps, while  Increasing Octane Rating of Pump Fuel, Knock Protection. Run More Boost and Timing, Make More Power

Water/methanol injection for gas engines is a proven means for effectively reducing engine inlet air temperatures and suppressing harmful detonation on forced induction and high compression naturally aspirated (NA) race engines. This allows racers to reliably increase boost and advance ignition timing—without using high-octane racing fuel—for power gains of up to 20%. AEM’s Water/Methanol Injection Systems utilize the most robust hardware combined with more advanced features than any other comparably priced water/methanol system.

The on-demand progressive controller in AEM’s Boost Dependent PN30-3302 tank-less Water/Methanol Injection kit bases injection flow on manifold pressure using an on-board MAP sensor (up to 35 PSI of boost) to ensure the proper amount of water/methanol injection at all points along an engine’s power curve.

AEM’s engineers spent extensive time developing the controller’s flow control strategy for a more linear flow output delivery. This means that the flow delivery better matches an engine’s need for water/methanol injection, which further optimizes charge air cooling and detonation control.

The new controller design features large, turn-resistant knobs and larger numbering to easily set accurate start and full activation points, with covered status LED and test buttons for added splash resistance. A plug is integrated into the controller housing for mating to the redesigned wiring harness’s positive-lock connector. The Boost Dependent controller housing has a molded-in, barbed nipple to accept a boost hose and a wiring legend on the back, integrated fuse and molded mounting tabs.

AEM’s Boost Dependent Water/Methanol Injection kit’s wiring harness is terminated with a positive-lock connector on one end and has color-coded wires to ease installation. Both the power and ground wires for the pump are included in the harness which simplifies the wiring process and eliminates any chance of the pump accidentally activating from a short in the system. An additional wire is included for adding an optional on/off solenoid to stop fluid flow when the system is inactive.
  • Boost Dependent controller features on-board MAP sensor with large adjustment knobs, integrated plug for harness connection, integrated fuse, covered status light and test button for enhanced splash resistance and mounting tabs
  • Wiring harness is terminated with a positive-lock connector on one end with color-coded wires to ease installation, power and ground wires for the pump and additional wire for optional on/off fluid solenoid
  • “Boost Safe” failsafe output included)
  • Internally-bypassed water/methanol injection pump does not cycle on an off and provides quiet, smooth operation. It features robust construction including integral hose fittings, EPDM seals and a Santoprene diaphragm that provides consistent and reliable fluid delivery
  • Precision-machined billet-aluminum injector with integral check valve
  • Three interchangeable injector nozzles to cover a wide variety of HP levels (250cc/min, 500 cc/min & 1,000cc/min)
  • Tank-less 35 PSI Boost Dependent gas water/methanol system (AEM Part 30-3300 includes controller with on-board MAP sensor and 1 gallon tank)
  • 20 feet of injection tubing included
  • LED dash light for system status and low fluid warning

Important Safety Notice Regarding Methanol

AEM strongly recommends that users never exceed a 50% methanol concentration when using any AEM Water Methanol system or component.

All AEM Water/Methanol injection systems and components (pump, lines, fittings, filter, flow sensor, tank, and nozzles) are 100% chemically compatible with methanol. However, for safety reasons we strongly recommend that users never use more than a 50% methanol concentration in our systems.

Methanol is a toxic and highly flammable chemical. 100% Methanol ignites easily and burns vigorously with an almost undetectable flame. Methanol can be absorbed through the skin and even small amounts can cause blindness or even death. Using this fluid at high pressures, without dilution, in an under-hood environment with nylon lines and push-to-connect fittings is very unsafe. The performance advantages of using greater than 50% methanol concentrations are small, if they exist at all. However, the safety issues are very real and far outweigh any perceived benefit of running high concentrations of methanol.

AEM PART NUMBER 30-3302
AEM V2 Water/Methanol Injection Kit (Turbo/FI Applications) With Tank

AEM V2 Water/Methanol Injection Kit (Turbo/FI Applications) With Tank

Reduce Intake Air Temperatures and Exhaust Gas Temps, while  Increasing Octane Rating of Pump Fuel, Knock Protection. Run More Boost and Ti ...

£ 389.99
add to cart
show details
Reduce Intake Air Temperatures and Exhaust Gas Temps, while  Increasing Octane Rating of Pump Fuel, Knock Protection. Run More Boost and Timing, Make More Power

Please select your desired tank size from the drop down menu before adding your selection to the shopping cart



AEM30-3300WaterMetanolInjectionKit4LTank400pxAEM30-3301WaterMetanolInjectionKit19LTank400px Water/methanol injection for gas engines is a proven means for effectively reducing engine inlet air temperatures and suppressing harmful detonation on forced induction and high performance naturally aspirated race engines. This allows racers to reliably increase boost and advance ignition timing—without using high-octane racing fuel—for power gains of up to 20%. AEM’s Water/Methanol Injection Systems utilize the most robust hardware combined with more advanced features than any other comparably priced water/methanol system.

The on-demand progressive controller in AEM’s Boost Dependent PN30-3300 Water/Methanol Injection kit bases injection flow on manifold pressure using an on-board MAP sensor (up to 35 PSI of boost) to ensure the proper amount of water/methanol injection at all points along an engine’s power curve.

AEM’s engineers spent extensive time developing the controller’s flow control strategy for a more linear flow output delivery. This means that the flow delivery better matches an engine’s need for water/methanol injection, which further optimizes charge air cooling and detonation control.

The new controller design features large, turn-resistant knobs and larger numbering to easily set accurate start and full activation points, with covered status LED and test buttons for added splash resistance. A plug is integrated into the controller housing for mating to the redesigned wiring harness’s positive-lock connector. The Boost Dependent controller housing has a molded-in, barbed nipple to accept a boost hose and a wiring legend on the back, integrated fuse and molded mounting tabs.

AEM’s Boost Dependent Water/Methanol Injection kit’s wiring harness is terminated with a positive-lock connector on one end and has color-coded wires to ease installation. Both the power and ground wires for the pump are included in the harness which simplifies the wiring process and eliminates any chance of the pump accidentally activating from a short in the system. An additional wire is included for adding an optional on/off solenoid to stop fluid flow when the system is inactive.

AEM’s Boost Dependent, PN 30-3300 gasoline Water/Methanol Injection System’s compact 1 gallon tank includes a high tech conductive low fluid level indicator with a positive lock connector and color matched wires to the wiring harness.
  • Boost Dependent controller features on-board MAP sensor with large adjustment knobs, integrated plug for harness connection, integrated fuse, covered status light and test button for enhanced splash resistance and mounting tabs
  • Wiring harness is terminated with a positive-lock connector on one end with color-coded wires to ease installation, power and ground wires for the pump and additional wire for optional on/off fluid solenoid
  • “Boost Safe” failsafe output included
  • Internally-bypassed water/methanol injection pump does not cycle on an off and provides quiet, smooth operation. It features robust construction including integral hose fittings, EPDM seals and a Santoprene diaphragm that provides consistent and reliable fluid delivery
  • Precision-machined billet-aluminum injector with integral check valve
  • Three interchangeable injector nozzles to cover a wide variety of HP levels (250cc/min, 500 cc/min & 1,000cc/min)
  • 1 gallon tank(10" x 8.5" x 4.25") with integral conductive low-fluid sensor and positive lock connector (tank-less water/methanol gas systems available, AEM Part 30-3302 includes controller with on-board 35 PSI MAP sensor)
  • 20 feet of Nylon injection tubing included
  • LED dash light for system status and low fluid warning

Important Safety Notice Regarding Methanol

AEM strongly recommends that users never exceed a 50% methanol concentration when using any AEM Water Methanol system or component.

All AEM Water/Methanol injection systems and components (pump, lines, fittings, filter, flow sensor, tank, and nozzles) are 100% chemically compatible with methanol. However, for safety reasons we strongly recommend that users never use more than a 50% methanol concentration in our systems.

Methanol is a toxic and highly flammable chemical. 100% Methanol ignites easily and burns vigorously with an almost undetectable flame. Methanol can be absorbed through the skin and even small amounts can cause blindness or even death. Using this fluid at high pressures, without dilution, in an under-hood environment with nylon lines and push-to-connect fittings is very unsafe. The performance advantages of using greater than 50% methanol concentrations are small, if they exist at all. However, the safety issues are very real and far outweigh any perceived benefit of running high concentrations of methanol.

AEM Part Numbers
V2 Water Methanol Kit With 4 Liter Tank - 30-3300 V2 Water Methanol Kit With 19 Liter Tank - 30-3301
AEM Water Methanol Injection Kit Inline Filter

AEM Water Methanol Injection Kit Inline Filter

AEM’s Water/Methanol Injection Filter can filter particulates as small as 40 microns. It protects the working parts of the water/methanol ...

£ 28.99
add to cart
show details
AEM’s Water/Methanol Injection Filter can filter particulates as small as 40 microns. It protects the working parts of the water/methanol system and the engine from particulates in the water/methanol mixture when installed in-line before the water/methanol pump, and can be used on virtually any water/methanol injection system using ¼” OD tubing.

AEM30-3003WaterMethanolKitFilter400px

Why An Inline Filter Is A Good Idea.

If you are using a Water/Methanol Injection System it may greatly increase pump life to use a water/methanol filter. The AEM Water/Methanol Injection Filter prevents foreign particles as small as 40 microns from clogging or damaging pumps, injection nozzles check valves or flow sensors. The AEM Water/Methanol Injection Filter uses fittings for use with 1/4" OD nylon tubing, so it fits most Water/Methanol injection kits on the market today!
  • Simple to install, takes less than a minute!
  • Fits virtually every Water/Methanol system on the market.
  • Polypropylene housing - rugged material that is compatible with high concentrations of methanol.
  • Completely Serviceable Assembly - can be disassembled, cleaned and reused for a long service life.
  • Stainless Steel mesh strainer - AEMs custom mesh strainer filters down to 40 microns - MUCH smaller than similar filters.
  • Large Filtering Area assure long service life and does not significantly reduce flow.
  • Micronic Mesh Screen out-performs sintered filters in both filtering and serviceability.
AEM PART NUMBER - 30-3003

Shopping Cart

 

Shop categories

ajax
ajax