GReddy Sports OX Oil Filters use “double pleats” folding technology on the inner filter to provide a maximum filtration surface for contaminant removal. It is also very durable and easily removed. Ideal for GReddy Oil, Oil Coolers, and Oil Filter Relocation kits.
Suitable for both RX-8 and RX-7 applications.
Trust GReddy Compression Tube for FC3s
The GReddy intake "Elbow" designed as a straight fit to the throttle body found on the FC3s.
Designed to provide a smoother flow of ...
The GReddy intake "Elbow" designed as a straight fit to the throttle body found on the FC3s.
Designed to provide a smoother flow of air in to the throttle body the inlet side it 70mm diameter
Depending on your style/design of intercooler you may require different couplers or piping.
The Trust GReddy intake elbow comes with a pre-tapped boss designed to accept the stock intake air sensor.
Please allow up to 21 days for delivery when this item is out of stock
Thanks to our close association with the new UK distributor of Goopy Performance products Essex Rotary can now offer this superb proven more durable alternative to the standard Mazda Apex Seals.
Goopy Apex seals have become renowned for their reliability by withstanding up to 50psi in Drag Racing and still not failing and have even withstood detonation that the Mazda Apex seal could only dream of.
This makes these High Performance Apex seals not only ideal for any N/A, Turbo or Supercharged RX-7 but also ANY standard or tuned REW or 13bt engine .
Also available for the RX-8 engines these seals can be included in your Essex Rotary engine rebuild upon request at a small additional cost.
Sold at a set of 6 complete seals these will easily replace the stock apex seals found in all series 4- series 8 RX-7 engines.
Goopy 2 mm apex seals are .075" (1.905mm) thick and you should be able to slide a .0015" feeler gauge into the rotor apex slot with a new apex seal in place.
Goopy Performance 13B 2 mm oversized apex seals measure .078" +/- .001" (1.981mm +/- 0.025mm). If your rotor slot measures .077 - .078", then you may benefit from our oversized 2 mm seals which will allow you to re-gain the .0015 suggested clearance.
If your gap with the seal in place measures .002-.005" it is still usable, but keep in mind that tighter clearances means greater sealing characteristics.
Due to their increased popularity please allow up to 21 days for delivery
Racing Beat Thermal Bypass Pellet
The Racing Beat Eccentric Shaft Thermal Bypass Pellet Replacement can be installed on any 1986 and later eccentric shaft. from RX-8 through ...
The Racing Beat Eccentric Shaft Thermal Bypass Pellet Replacement can be installed on any 1986 and later eccentric shaft. from RX-8 through to late RX-8's
The Thermal pellet is designed to delete the traditional oil thermostat found in the front or the eccentric shaft, this unit is known to fail over time and always fails in the closed position reducing oil flow to your engine however you will never know.
Highly recommended to fit at the time of a rebuild.
Racing Beat Oil Baffle Plate for 86-92 FC3s
The Racing Beat-designed and manufactured Oil Baffle Plate slows the return of engine oil as it drains from the engine into the pan. In slow ...
The Racing Beat-designed and manufactured Oil Baffle Plate slows the return of engine oil as it drains from the engine into the pan. In slowing the oil's return, air that has been suspended in the oil (as foam) is allowed more time to separate from the oil.
Removing this trapped air both improves the ability of the oil to transfer heat and reduces pressure drops at high RPM. The plate is sandwiched between the engine and the oil pan. It is recommended that two oil pan gaskets be used, one below and one above the plate, to provide proper sealing. Gaskets are not supplied, but are available separately if needed.
Please allow up to 28 Days for Delivery of items if out of stock.
Stationary Gear Bearings FB, FC & 192 + Auto RX-8
Sold as a Pair these stationary gear bearings where used in many of the early Rotary engines
Sold as a Pair these stationary gear bearings where used in many of the early Rotary engines
These include
RX-7 FB/SA22c
RX-7 FC EGI
RX-7 FC Turbo II
RX-8 192ps (4 Port Manual)
Rx-8 Auto (4 Port Automatic)
These bearings have fewer "windows" but are the correct bearings for most 12a and early 13b engines (with the exception of the 13b REW found in the RX-7 FD3s)
If your looking at these for your 4 port RX-8 engine then a popular upgrade is the high power multi window bearings though there is no locator notch found on the high power bearings here at Essex Rotary we install them in conjunction with a high quality "bearing lock" compound to help keep them in place.
Sold as a pair of bearings.
if out of stock please allow up to 3 weeks for delivery, if your in need of these parts quickly then we recommend you give us a call prior to ordering.
Rotor Bearing Set for RX-7 FB and FC
Genuine Mazda Rotor Bearings
These are the standard rotor bearings for 12a and Early 13b's including the RX-7 FB/SA22c and FC3s ...
Genuine Mazda Rotor Bearings
These are the standard rotor bearings for 12a and Early 13b's including the RX-7 FB/SA22c and FC3s
Please note these are the most common size however we are able to offer an oversized option for the Fc3s if required
These bearings are sold as a pair (2 bearings) so one for each rotor.
Please be aware that if these bearings are out of stock it may take up to 3 weeks to get your parts to you, if you require fast delivery then we recommend you contact us prior to placing your order so that we may check availability and pricing for express delivery.
Royal Purple Max-Tuff Synthetic Assembly Lube
This Awesome Assembly Lube is used on all our engine rebuilds here at Essex Rotary, It makes the assembly of tight fitting close tolerance p ...
This Awesome Assembly Lube is used on all our engine rebuilds here at Essex Rotary, It makes the assembly of tight fitting close tolerance parts a breeze while still offering excellent protection for parts like stationary gears on initial start up.
Here is what Royal Purple have to say.
Max-Tuff is an ultra-tough, synthetic lubricant. It’s designed for engine builds and repairs. Max-Tuff utilizes unique, synthetic molecules that adhere to metal surfaces to create a formidable, load-bearing physical barrier between surfaces. This minimize the metal-to-metal contact and wear in boundary lubrication conditions, and provides excellent protection against rust and corrosion of both ferrous and nonferrous metals.
PERFORMANCE ADVANTAGES
Greater wear protection
Clean, efficient equipment
Extends equipment life
Compatible with conventional mineral and synthetic oils
Non-foaming
Outstanding rust / corrosion protection
High temperature service capability
Sold in an 8oz bottle
Super Now Response Up Kit for RX7 FC3s TII
Blanking plate kit for RX-7 FC3s Turbo II from the famous Japanese rotary tuner Super Now
This kit is used when removing Air Control ...
Blanking plate kit for RX-7 FC3s Turbo II from the famous Japanese rotary tuner Super Now
This kit is used when removing Air Control Valve (ACV) to simplify the intake manifold and engine bay.
Made from 8mm aluminium with an anodized finish.
Not suitable for Turbo II engines still running the stock air pump system.
This Kit contains 4 blanking plates.
Please allow up to 3 weeks if these items are not in stock. if you require this part quickly please contact us before ordering.
GFB Light Weight Dual V Belt Alternator Pulley for RX-7 SA22c,FB3s & FC3s
Mazda 12A/13B Engine Twin V-belt Alternator Pulley
GFB lightweight pulley kits are made from aircraft-grade 6061-T6 aluminium and o ...
Mazda 12A/13B Engine Twin V-belt Alternator Pulley
GFB lightweight pulley kits are made from aircraft-grade 6061-T6 aluminium and offer faster acceleration through significant weight reduction on the crankshaft. The effect is similar to a lighter flywheel, and the car feels more lively and willing to rev.
Most of our kits are underdriven, which means the accessories are driven slightly slower to reduce parasitic losses. It should be noted that our underdrive pulley kits do NOT adversely affect the operation of the accessories. If they did, we would not sell them! Lightweight Alloy Pulley
Improved throttle response and acceleration through significant reduction of rotating mass
Engine feels more free-revving
Under-driven kits offer more power through reduction of parasitic losses from the accessories with NO adverse affects on their operation
Suitable for Sa22c, FB3s and FC3s Engine setups.
Compatible with both 12a and 13b Engine that run the old style V Drive Belts.
Go Fast Bits Product Code: 2215
Please allow up to 28 days for delivery of this pulley if not in stock.
The Mazda Factory Race (MFR) rotor bearings for all 12A & 13B engines are the best bearings available of engine operation near or above 8500 RPM. The rotor bearings are manufactured with a deep groove for additional oil storage and offer an additional .0005" (approximate) clearance. These bearings can be used in 1973 and earlier engines by grinding off the indexing tab.
Competition bearings have 0.01 inch deeper oil groove and provide 0.0005 inch more clearance than stock bearings. Thinner overlay material improves bearing service life.
These bearings are special order only and can take up to 6 weeks for delivery. They are sometimes out of stock at Mazda HQ Japan so can take longer. we would recommend ordering your competition bearings early to avoid disappointment.
Genuine Mazda Factory Race Part
Use in place of stock rear bearing. 3-window type. Recommended for any engine used at 8000 rpm and above. Increases oil flow to the inside of eccentric shaft and to rotors.
If you are installing this bearing in to a Manual RX-7 FD3s of 231ps RX-8 Rear Stationary Gear we would recommend getting an indexing groove cut in to the rear face of the stationary gear in order to locate and hold this bearing correctly. The location should be in the same place as that found on Auto Rear Stationary gears and those earlier then the FD3s. Stationary gears from the Automatic FD3s and RX-8 including the 192ps manual RX-8 should have this indexing groove in them already.
These bearings are special order only and can take up to 6 weeks for delivery. They are sometimes out of stock at Mazda HQ Japan so can take longer. we would recommend ordering your competition bearings early to avoid disappointment.
THESE BEARINGS ARE SOLD INDIVIDUALLY
Goopy Performance 3mm Apex Seals for 13b Engines
NOT ALL 13B ENGINES RUN 3MM APEX SEALS, PLEASE CHECK YOUR APPLICATION BEFORE ORDERING.
Thanks to our close association with the new UK di ...
NOT ALL 13B ENGINES RUN 3MM APEX SEALS, PLEASE CHECK YOUR APPLICATION BEFORE ORDERING.
Thanks to our close association with the new UK distributor of Goopy Performance products Essex Rotary can now offer this superb proven more durable alternative to the standard Mazda Apex Seals.
Goopy Apex seals have become renowned for their reliability by withstanding up to 50psi in Drag Racing and still not failing and have even withstood detonation that the Mazda Apex seal could only dream of.
This makes these High Performance Apex seals not only ideal for any N/A, Turbo or Supercharged 13b but also ANY standard or tuned 13b engine running 3mm seals .
Goopy Performance recommend .0015" of clearance between the apex seal and the rotor slot for all applications, boosted or naturally aspirated.
3 mm 13B Goopy Apex Seals are .115" (2.921mm) thick, and you should be able to slide a .0015" feeler gauge into the rotor apex slot with a new apex seal.
Goopy oversized 3 mm seals measure .118" + / - .001" (2.997mm +/- 0.025mm). If your rotor slot measures .018" - .020", you may benefit from our oversized 2 mm seals which will allow you to re-gain the .0015" suggested clearance.
Also available for the RX-8 engines these seals can be included in your Essex Rotary engine rebuild upon request at a small additional cost.
Sold at a set of 6 complete seals these will easily replace the stock apex seals found in some factory 13b engines or builds with 3mm machines slots.
Due to their increased popularity please allow up to 21 days for delivery
Pineapple Racing Solid Dowel Pins RX-7 FC, FD, 20b
Pineapple Racing Solid Dowel Pins
Helps prevent cracking the plates from hp loads or “ping” (esp. important in the 20B and ...£ 79.99
Helps prevent cracking the plates from hp loads or “ping” (esp. important in the 20B and Series 5 & earlier turbo engines)
Spreads the load across the length of the engine.
Helps to insure a true engine centerline which reduces engine failure and increasing bearing life
Using an external oil line provides a more even oil pressure to the main bearings
Low cost, easy installation
Available for: 12A, 13B and 20B (12a and 20b Special Order)
Custom lengths available (Special Order)
Pineapple Racing Solid Dowel Pins provide an easy, cost effective aid to hp and “ping” loads causing plate cracking or engine damage from loss of clearance from engine flex. Our super strong proprietary material has been meticulously machined to provide what we feel are the most accurate and consistently machined solid dowel pins on the market. The O.D. is accurate to 50 millionth’s! That’s 0.00005”. We “lightly” tapped one end for use with a Dowel Pin Puller.
Replace just the lower dowel pins helps to insure your engine’s centerline remains true. It is a great update requiring no machining.
Replace both lower and upper dowel pins for the maximum improvement. Replacing the upper dowel pins requires the installation of an external oil feed line to the front main oil galley to replace the OEM galley in the OEM dowel pins. Our Oil Pedestal Adapter kit makes this a simple job that can be done with simple hand tools and an electric drill.
High horsepower and the shock loads from “ping” put a tremendous load against the rotor housings. The load deflects the rotor housings outwards, pushing the dowel pin with them. The dowel pins are retained by their fit into the cast iron plates. If the loads are too high, the upper dowel pin can cause the plate(s) to crack. Additionally, since the upper dowel pins are also used as an oil galley, a massive oil leak is also possible. The OEM 20B is especially prone to this type of damage, and with the price of the “thick” center plate near $1800us, preventing this type of damage pays for itself.
The Pineapple Racing Oil Pedestal Adapter is a stylish, Nickel plated rotor shaped adapter. It easily installs between the existing oil filter pedestal and the rear plate. It features a ¼”NPT port for an external oil line and an 1/8” NPT port for oil pressure or oil temperature.
Please allow up to 28 days for delivery if not in stock.
Pineapple Racing Heavy Duty (HD) Water Seal Kit for RX7 FC3s S5
This is Pineapple Racing's exclusive Heavy Duty Water Seal kit. Pineapple Racing tested these seals for over 7 years in numerous street and ...
This is Pineapple Racing's exclusive Heavy Duty Water Seal kit. Pineapple Racing tested these seals for over 7 years in numerous street and track cars before offering them to our customers. They have proven to be a significant upgrade over the stock water seals. Pineapple Racing use them in all their 5-year warranty motors.
Also, these seals are re-usable if you need to reopen the motor to freshen it, as long as the mileage is not too high or the engine too overheated. In other words, if you make a mistake and blow up your engine or perhaps improperly clearance the seals or whatever, these seals can be removed, allowed to "rest" for about 30 minutes and be reused when you put the engine back together. Stock water seals must be disposed of when freshening an engine, even with just a couple heat cycles.
Kit includes
Water jacket o-rings
Front cover o-ring (and backup washer, if needed application dependent)
Dowel o-rings
Rear stationary gear o-ring
Oil pedestal o-rings or Gasket (depending on application).
Oil Metering Pump "O" Ring
Dowty Washer Set (Tension Bolt Washers)
Please note this kit is for a Series 5 RX-7 FC Engine,
Please allow around 28 days for delivery if not in stock.
Racing Beat Modified Holley Intake Kit 74-85 12A / 13B
PLEASE SELECT YOUR CORRECT MODEL APPLICATION FROM THE DROP DOWN MENU NET TO THE "ADD TO CART" BUTTON £ 990.00
PLEASE SELECT YOUR CORRECT MODEL APPLICATION FROM THE DROP DOWN MENU NET TO THE "ADD TO CART" BUTTON
From the selection on the drop down box below we offer the popular Racing Beat-modified High Performance Holley Intake System Kit for the 1974-1985 12A & 13B with stock port, street port and bridge port engines.
One of most significant benefits of this complete ready-to-go kit is that is takes all the guesswork, trial-and-error, and frustration out of attempting to assembly your own intake kit! We've taken over 40 years of our rotary engine experience and know-how and combined it for you in this complete, ready-to-install kit. Our intake kits has been thoroughly developed and tested using our in-house engine dyno to ensure maximum performance for each specific engine application.
The heart of each intake system is a performance-proven Holley carburetor. Depending on the requirements of each specific application, the carburetor is disassembled by Racing Beat's carburetor technicians then reworked, retuned, and reconfigured specifically for use with a designated rotary engine application. This process is not a simple "re-jetting" project, but a complex series of steps requiring machining, drilling and reconfiguring of the main and metering bodies, adjustment of the float bowls, and complete replacement of all jets.
Headers must be used with these street port intake systems to achieve maximum horsepower gains.
The carburetors and manifolds used in these Holley kits are also available separately in the "Holley Components" section. Also see the "Intake" section for other related intake components.
Note: Installation of this kit requires use of a high performance fuel pump delivering 6 psi @ 20 gph.
PLEASE SELECT YOUR CORRECT MODEL APPLICATION FROM THE DROP DOWN MENU NET TO THE "ADD TO CART" BUTTON
Please Note that this item is special order only, and is subject to our non return policy for special order items under our T&C's of sale. for more information please check out T&C's here