The GReddy intake "Elbow" designed as a straight fit to the throttle body found on the FC3s.
Designed to provide a smoother flow of air in to the throttle body the inlet side it 70mm diameter

Depending on your style/design of intercooler you may require different couplers or piping.
The Trust GReddy intake elbow comes with a pre-tapped boss designed to accept the stock intake air sensor.

Please allow up to 21 days for delivery when this item is out of stock

GReddy Blow Off Valves are easily adjustable to eliminate compressor surge and preventing premature boost leakage, while increasing boost response between shifts. Each valve is made of durable cast and billet aluminum frame and the valve to diaphragm ratio provides performance that cheap piston types cannot offer. The spring stiffness adjustment screw and the three different models give the GReddy user the option to match vehicles with mild upgrades to heavily tuned engines The Type FV The Brand New GReddy FV has the latest Floating Valve technology.The unique "floating valve" design incorporates a revised adjustable dual spring system, while retaining the advantages of the previous models push valve structure and diaphragm control. The improved design makes spring preload setting less dependant on the idle, while providing increased response, valve travel, flow and resistance to premature valve lift under all conditions. The new GReddy FV BOV retains the same mounting, outlef and position as previous GReddy Type RS and Type RZ models, making retrofitting the new type FV to existing applications possible. Please allow up to 28 days for delivery when out of stock

High flow air filter for your RX7, serviceable every 50'000 miles this filter never needs replacing.

Water Methanol Injection at its finest!

The gasoline Stage 1 Boost Cooler™ kit is available for forced induction applications that are either fuel injected or carbureted. Operation is very simple: the system starts injecting when the boost switch reaches the user-adjustable point and it injects a fixed amount of fluid through the nozzle until the switch opens again. This makes it a good choice for low boost setups looking for an octane enhancement and cooler intake charge. Activation can also be set up through any other user-chosen switch, such as a full throttle switch, etc.

Boost Cooler Waterinjection

Obtain up to 10-25% more power in your turbo- or supercharged engine, even if it´s pre-tuned, by using the Boost Cooler?-Water/Methanol Injection System!

The main function of the Boost Cooler is to suppress detonation caused by high temperature and pressure developed within the combustion chamber when the effective compression ratio has been taken beyond the auto-ignition point by either a turbo or a supercharger. Water, with its high latent heat content, is extremely effective for controlling not only the onset of detonation but also the production of oxides of nitrogen in the modern leanburn engines.

Furthermore, the Boost Cooler doesn't create an intake restriction like an intercooler, and unlike race gas, it reduces intake air temps up to 60°C and improves charge air density too!

Snow Performance systems effectively steam clean intake when they inject. This reduces carbon build up. The Boost Cooler? can be installed in a matter of hours without having to remove bumpers or do custom intake piping.

Kit includes:

• UHO (Ultra High Output) Pump
• 3 Quart Reservoir
• 2 Nozzles To Cover a Wide Range of Horsepower
• Required Hardware Needed For Installation
• Comprehensive Instructions

Note: Safe Injection can not be used with Stage 1 Gasoline Systems

Water Methanol Injection at its finest!

Snows most popular kit for low/mid boost engines (<1.7bar) - with Variable Injection (VC-20) and 300PSI/20bar Pumpsystem !

This kit progressively injects more or less water or water/alcohol, according to manifold boost pressure. The system is applicable for turbo/supercharged engines making up to 1.5bar of boost pressure. It has two dials to set the start and full points to tailor the delivery to your engines needs. Progressively injecting according to boost pressure allows for the most power over the widest range of rpms.

Boost Cooler Water injection

Obtain up to 10-25% more power in your turbo- or supercharged engine, even if it´s pre-tuned, by using the Boost Cooler?-Water/Methanol Injection System!

The main function of the Boost Cooler is to suppress detonation caused by high temperature and pressure developed within the combustion chamber when the effective compression ratio has been taken beyond the auto-ignition point by either a turbo or a supercharger.

Water, with its high latent heat content, is extremely effective for controlling not only the onset of detonation but also the production of oxides of nitrogen in the modern lean burn engines.Furthermore, the Boost Cooler doesn't create an intake restriction like an intercooler, and unlike race gas, it reduces intake air temps up to 60°C and improves charge air density too!

Snow Performance systems effectively steam clean the intake when they inject. This reduces carbon build up. The Boost Cooler? can be installed in a matter of hours without having to remove bumpers or do custom intake piping.

Boost controlled variable injection

This kit uses manifold boost pressure to determine when and how much fluid to inject. Proportionally injecting according to boost pressure gives the most accurate delivery of water-methanol and allows the most cooling and performance improvement over the widest range. More power and driveability is the result! It can be used on any forced induction engine.

The most suitable are the centrifugal supercharged and turbocharged engines, as they build boost is a more progressive manner concerning water-methanol injection. The positive displacement blower engines will work, but it might take more work to dial in the delivery. New: You can switch to a 0-5 Volt output signal from the Mass Air for injection controlling.

Kit includes:

• UHO (Ultra High Output) Pump
• 3 Quart Reservoir
• Digital Variable Controller
• 2 Nozzles To Cover a Wide Range of Horsepower
• All Required Hardware Needed For Installation
• Comprehensive Instructions

Features:

• VC-20 control unit, Boost/MAP controlled, variable injection
• Efficient Intercooling, up to 60°C lower air intake temperature
• Achieve approx. 116-Octan rating, by using ordinary 95-Octan gasoline
• Reduces EGT and oil temperatures
• Allows you to run safely more boost and/or more timing
• Reduces thermical stress on NOS, LPG/Autogas and pre-tuned engines like chiptuning & higher boost levels
• No wear issues, only clean combustion chambers
• No loss of boost as with an intercooler
• Reduces the specific fuel consumption
• Easy installation

Water Methanol Injection at its finest!

The latest development from Snow Performance!
Complete kit with freely programmable 52mm OLED-gauge and optionally Dual Stage Technology.

Boost Cooler Water Injection

Obtain up to 10-25% more power in your turbo- or supercharged engine, even if it´s pre-tuned, by using the Boost Cooler™-Water/Methanol Injection System!
The main function of the Boost Cooler is to suppress detonation caused by high temperature and pressure developed within the combustion chamber when the effective compression ratio has been taken beyond the auto-ignition point by either a turbo or a supercharger.

Water, with its high latent heat content, is extremely effective for controlling not only the onset of detonation but also the production of oxides of nitrogen in the modern lean burn engines.Furthermore, the Boost Cooler doesn't create an intake restriction like an intercooler, and unlike race gas, it reduces intake air temps up to 60°C and improves charge air density too!

Snow Performance systems effectively steam clean the valves, valve seats, and even the piston tops and intake when they inject. This reduces carbon build up. The Boost Cooler™ can be installed in a matter of hours without having to remove bumpers or do custom intake piping.

52mm OLED Control Unit

The all new Snow Performance Stage 2 Boost Cooler water-methanol injection system comes fully revamped for all boosted (turbo- and supercharged) vehicles and uses a progressive 52mm-gauge style controller that proportionally injects more or less according to boost pressure.
Start and full points are adjustable for engagement and delivery curve to match what the engine requires. Proportionally injecting according to boost pressure gives an accurate delivery of water-methanol and allows cooling and performance improvements over a wide range for improved drivability.

Displays :

• Boost pressure (S2E / EURO-Edition in BAR)
• Boost Cooler percentage of injection
• Low level of the fluid reservoir
• Secondary nozzle activation (Dual Stage Technology, optionally as upgrade)
• 2 specific fault modes (Clogged line, broken line)

Dual Stage Technology (DST)

The Stage 2 has the ability to progressively command 2 Hyper-Sonic™ Nozzles independently of one another. This sophisticated dual stage injection management yields the highest increases in HP and cooling along all stages of the engine allowing you to greatly increase the boost & timing of your vehicle safely.

Easy Installation

The settings on OLED control unit can be made within a few seconds without any prior knowledge. The only thing you need to determine is at what boost pressure the injection is to begin and what the maximum boost pressure is. - The variable injection of the Boost Cooler is performed within these two preset boost pressure points. By using the optionally Dual Stage Technology, you´re able to set a 2nd nozzle mapping for optimized injection quantity especially at higher engine load states.

Boost Cooler Stage 2 Power-MAX - Perfect for nearly all turbocharged engines

For positive displacement superchargers (Eaton, Twin Screw) and small fast spooling turbos see (e.g. K03/K04 turbochargers) use the Boost Cooler Stage 2 MAF or our Stage 3 kits for best performance.

Stage 2 POWER-MAX™ Europe Edition

Die Europe-Edition (display & programming in BAR) is exclusively available only by Snow Performance Europe and its European authorized dealers.

Features :

• Boost referenced injection control For use with all centrifugal superchargers (ProCharger, Vortech) and large turbos (*)
• Complete with our industry leading 300 PSI UHO pump and Hypersonic Nozzles™
• Dual Stage Technology 2 nozzle control independently of one another (Optional, Upgrade Art.No.: SP10350 required)
• 52mm gauge style progressive water-methanol controller
• Dual tone 7 color OLED screen
• Efficient Intercooling, up to 60°C lower air intake temperature
• Achieve approx. 116-Octan rating, by using ordinary 95-Octan gasoline
• Reduces EGT and oil temperatures
• Allows you to run safely more boost and/or more timing
• Reduces thermical stress on NOS, LPG/Autogas and pre-tuned engines like chiptuning & higher boost levels
• No wear issues, only clean combustion chambers
• No loss of boost as with an intercooler
• Reduces the specific fuel consumption
• Easy installation

Water Methanol Injection at its finest!

Our Top system for your Turbo-/Supercharged car. 2D-Mapping thrugh fuel injection and/or boost. Easy programmable LCD-display incl. new Dual Stage Technology and terminated weather tight OEM harnessed wiring connections !
Award winning system - The controller creates a delivery map based boost and/or EFI signal. For all charged and naturally aspirated engines with traditional EFI system.

Boost Cooler Waterinjection

Obtain up to 10-25% more power in your turbo- or supercharged engine, even if it´s pre-tuned, by using the Boost Cooler™-Water/Methanol Injection System!
The main function of the Boost Cooler is to suppress detonation caused by high temperature and pressure developed within the combustion chamber when the effective compression ratio has been taken beyond the auto-ignition point by either a turbo or a supercharger.

Water, with its high latent heat content, is extremely effective for controlling not only the onset of detonation but also the production of oxides of nitrogen in the modern leanburn engines.Furthermore, the Boost Cooler doesn't create an intake restriction like an intercooler, and unlike race gas, it reduces intake air temps up to 60°C and improves charge air density too!

Snow Performance systems effectively steam clean the valves, valve seats, and even the piston tops and intake when they inject. This reduces carbon build up. The Boost Cooler™ can be installed in a matter of hours without having to remove bumpers or do custom intake piping.

The Power Intake is the premier air filter designed to create pure horsepower. The intake funnels used in racing machines take advantage of a characteristic where air travels along the side of the side of surfaces. However, the center portion of the funnel is virtually unused. It is this concept that gave birth to the Dual Funnel design. A primary funnel on the top portion of the air cleaner was inserted to channel the air flow directly into the lower funnels at the base of the cleaner. This design was a huge success on the former Super Intake model. The Power Intake took this design and improved the flow characteristics. New funnel design, element material and air flow channeling characteristics make the Power Intake one of the most efficient air cleaners on the market today. By constructing the upper and lower funnel from a highly durable injected resin, engineers were able to construct the ideal shaped funnel previously not possible with the stainless steel material. Funnel shapes focused on increasing air speed without changing the flow direction of the intake air. The result is a high speed and smooth flow of air into the intake. The lower funnel has been engineered at a 14 degree curve for maximum efficiency. Also, the lower funnel position has been made even closer to the base of the cleaner to reduce drag and eliminate any _dead spotsb within the cleaner.

The Power Intake incorporates a newly developed material (layer filter of dry density fibers) which improves the element density. This allows maximum protection from foreign materials entering the engine. Compared with past model, the Power Intake has also succeeded in decreasing its ventilation resistance by about 10% (pressure loss) for maximum performance and protection. The Power Intake is dry-type filter and is trouble free. Some of the problems associated with wet type cleaners, such as oil sticking to the air flow meter, are a thing of the past. The Power Intake is basically maintenance free. Filter replacement, when necessary, can be done at a very low cost.

CONCEPT:

• Air filter with minimal air-flow restriction

CHARACTERISTICS:

• Dual funnel filter system minimizes intake turbulence

HKS Super SQV (Sequential Blow Off Valve) uses a unique sequential valve structure and a differential pressure control system, which allows for a broad operating range from low boost to high boost. Its Pull-Type relief design ensures stable operation regardless of the amount of boost pressure. The Super SQV will support new generations of turbocharged vehicles.

Universal Kit includes

• SQV Blow Off Valve
• O-ring,
• C-ring (Securing Clip)
•  Vacuum Hose T-fitting 6×4×6
• Vacuum Hose T-fitting 4×4×4
• Inline Air Filter and Tylap.

HKS Part Number: 71008-AK001

Please Allow up to 28 days for delivery for delivery.

Venturi Drive Super Sound Blow Off Valve - Release Type
The all new ribbed main body dissipates heat more effectively and the venturi shaped funnel creates a sharp dynamic sound.
Venturi Drive dump valves also feature "Dual Drive" for maximum response, a small port for low boost and a larger port for high boost.

The main purpose of the dump valves is to improve the response of the turbo by quickly releasing the boost pressure before the turbo stalls.

They are made from die cast polished aluminium with a brass piston and a rubber diaphragm, meaning they can easily cope with boost pressures up to 1.2 bar with the supplied spring.
There is an alternative hard spring for boost pressures above 1.2bar and also a soft spring available for very low boost applications.

Blitz VDSS Blow Off Valves  are also tension adjustable.





This kit includes everything needed to install onto your vehicle. (Please remember that most of these kits are designed to install on a standard setups so if you intend to install this on a single turbo conversion some modification may be required)
This kit is a Release Type

Please allow up to 28 days for delivery for this item if not in stock.

Essex Rotary bring you another high quality part from the legendary gods of rotary RE-Amemiya
The Response Cleaner Intake kit is a high quality filter designed to fit in to your FC3s Turbo II produced from 1989-1991

RE-Amemiya boasts a increase in response at higher revs in the FC3S due to their Dual-Entry Air filter intake design. The RE-Amemiya Response Cleaner Air Filter System will be a complete bolt-on kit and is an easy and clean way to increase both response and power for your FC3S.

Special Order only so please allow 2-6 weeks for delivery.

PLEASE SELECT YOUR CORRECT MODEL APPLICATION FROM THE DROP DOWN MENU NET TO THE "ADD TO CART" BUTTON

From the selection on the drop down box below we offer the popular Racing Beat-modified High Performance Holley Intake System Kit for the 1974-1985 12A & 13B with stock port, street port and bridge port engines.

One of most significant benefits of this complete ready-to-go kit is that is takes all the guesswork, trial-and-error, and frustration out of attempting to assembly your own intake kit! We've taken over 40 years of our rotary engine experience and know-how and combined it for you in this complete, ready-to-install kit. Our intake kits has been thoroughly developed and tested using our in-house engine dyno to ensure maximum performance for each specific engine application.

The heart of each intake system is a performance-proven Holley carburetor. Depending on the requirements of each specific application, the carburetor is disassembled by Racing Beat's carburetor technicians then reworked, retuned, and reconfigured specifically for use with a designated rotary engine application. This process is not a simple "re-jetting" project, but a complex series of steps requiring machining, drilling and reconfiguring of the main and metering bodies, adjustment of the float bowls, and complete replacement of all jets.

Headers must be used with these street port intake systems to achieve maximum horsepower gains.

The carburetors and manifolds used in these Holley kits are also available separately in the "Holley Components" section. Also see the "Intake" section for other related intake components.

Note: Installation of this kit requires use of a high performance fuel pump delivering 6 psi @ 20 gph.

PLEASE SELECT YOUR CORRECT MODEL APPLICATION FROM THE DROP DOWN MENU NET TO THE "ADD TO CART" BUTTON

Please Note that this item is special order only, and is subject to our non return policy for special order items under our T&C's of sale. for more information please check out T&C's here

If you are using a Water/Methanol Injection System and want to know exactly how much fluid you are actually injecting into your engine, the AEM Water/Methanol Flow Gauge is a must. It replaces the "dummy light" with actual data displayed on a smooth moving needle-type gauge that allows you to accurately monitor the status of your injection system in real time. The AEM Water/Methanol Flow Gauge comes with black and silver bezels and white and black faceplates for multiple color combinations.

AEM Part Number 30-5142

WHAT IT DOES

If you are using a Water/Methanol Injection System and want to know exactly how much fluid you are actually injecting into your engine, the AEM Water/Methanol Flow Gauge is a must. It replaces the "dummy light" with actual data displayed on a smooth moving needle-type gauge that allows you to accurately monitor the status of your injection system in real time. The AEM Water/Methanol Flow Gauge comes with black and silver bezels and white and black faceplates for multiple color combinations.

The gauge kit includes a precision flow sensor and fittings for use with 1/4" OD nylon tubing, so the AEM Water/Methanol Flow Gauge fits most Water/Methanol injection kits on the market today.

For best results the 0-1000CC Flow Gauge (AEM part# 30-5142) should be used on Water/Methanol kits injecting more than 500 cc/min and is ideal for those with the AEM Water/Methanol kit using the largest size or multiple sized nozzles. If you are using only a small or medium AEM nozzle, we suggest the 0-500CC Flow Gauge (AEM part# 30-5141)

WHY YOU WANT ONE

AEM's Water/Methanol Gauge gives you the exact amount of water/methanol you are spraying into your engine. Boost with the extra confidence of knowing your flow though your entire RPM and boost range. The gauge comes with both a white and black face place to perfectly match your interior.

PRODUCT FEATURES

• Gauge Readout from 0 to 1000cc
• Adjustable backlighting via a dial on the back of the gauge
• Includes black and silver interchangeable bezels and white and black faceplates
• 320 degree viewing area for unsurpassed resolution
• Fits virtually every water/methanol kit on the market today!
• 0-5v analog output included for use with data loggers and virtually any engine management system

Special Order Item Only.

Reduce Intake Air Temperatures and Exhaust Gas Temps, while  Increasing Octane Rating of Pump Fuel, Knock Protection. Run More Boost and Timing, Make More Power

Water/methanol injection for gas engines is a proven means for effectively reducing engine inlet air temperatures and suppressing harmful detonation on forced induction and high compression naturally aspirated (NA) race engines. This allows racers to reliably increase boost and advance ignition timing—without using high-octane racing fuel—for power gains of up to 20%. AEM’s Water/Methanol Injection Systems utilize the most robust hardware combined with more advanced features than any other comparably priced water/methanol system.

The on-demand progressive controller in AEM’s Boost Dependent PN30-3302 tank-less Water/Methanol Injection kit bases injection flow on manifold pressure using an on-board MAP sensor (up to 35 PSI of boost) to ensure the proper amount of water/methanol injection at all points along an engine’s power curve.

AEM’s engineers spent extensive time developing the controller’s flow control strategy for a more linear flow output delivery. This means that the flow delivery better matches an engine’s need for water/methanol injection, which further optimizes charge air cooling and detonation control.

The new controller design features large, turn-resistant knobs and larger numbering to easily set accurate start and full activation points, with covered status LED and test buttons for added splash resistance. A plug is integrated into the controller housing for mating to the redesigned wiring harness’s positive-lock connector. The Boost Dependent controller housing has a molded-in, barbed nipple to accept a boost hose and a wiring legend on the back, integrated fuse and molded mounting tabs.

AEM’s Boost Dependent Water/Methanol Injection kit’s wiring harness is terminated with a positive-lock connector on one end and has color-coded wires to ease installation. Both the power and ground wires for the pump are included in the harness which simplifies the wiring process and eliminates any chance of the pump accidentally activating from a short in the system. An additional wire is included for adding an optional on/off solenoid to stop fluid flow when the system is inactive. AEM strongly recommends that users never exceed a 50% methanol concentration when using any AEM Water Methanol system or component.

All AEM Water/Methanol injection systems and components (pump, lines, fittings, filter, flow sensor, tank, and nozzles) are 100% chemically compatible with methanol. However, for safety reasons we strongly recommend that users never use more than a 50% methanol concentration in our systems.

Methanol is a toxic and highly flammable chemical. 100% Methanol ignites easily and burns vigorously with an almost undetectable flame. Methanol can be absorbed through the skin and even small amounts can cause blindness or even death. Using this fluid at high pressures, without dilution, in an under-hood environment with nylon lines and push-to-connect fittings is very unsafe. The performance advantages of using greater than 50% methanol concentrations are small, if they exist at all. However, the safety issues are very real and far outweigh any perceived benefit of running high concentrations of methanol.

AEM PART NUMBER 30-3302

Reduce Intake Air Temperatures and Exhaust Gas Temps, while  Increasing Octane Rating of Pump Fuel, Knock Protection. Run More Boost and Timing, Make More Power

Please select your desired tank size from the drop down menu before adding your selection to the shopping cart

Water/methanol injection for gas engines is a proven means for effectively reducing engine inlet air temperatures and suppressing harmful detonation on forced induction and high performance naturally aspirated race engines. This allows racers to reliably increase boost and advance ignition timing—without using high-octane racing fuel—for power gains of up to 20%. AEM’s Water/Methanol Injection Systems utilize the most robust hardware combined with more advanced features than any other comparably priced water/methanol system.

The on-demand progressive controller in AEM’s Boost Dependent PN30-3300 Water/Methanol Injection kit bases injection flow on manifold pressure using an on-board MAP sensor (up to 35 PSI of boost) to ensure the proper amount of water/methanol injection at all points along an engine’s power curve.

AEM’s engineers spent extensive time developing the controller’s flow control strategy for a more linear flow output delivery. This means that the flow delivery better matches an engine’s need for water/methanol injection, which further optimizes charge air cooling and detonation control.

The new controller design features large, turn-resistant knobs and larger numbering to easily set accurate start and full activation points, with covered status LED and test buttons for added splash resistance. A plug is integrated into the controller housing for mating to the redesigned wiring harness’s positive-lock connector. The Boost Dependent controller housing has a molded-in, barbed nipple to accept a boost hose and a wiring legend on the back, integrated fuse and molded mounting tabs.

AEM’s Boost Dependent Water/Methanol Injection kit’s wiring harness is terminated with a positive-lock connector on one end and has color-coded wires to ease installation. Both the power and ground wires for the pump are included in the harness which simplifies the wiring process and eliminates any chance of the pump accidentally activating from a short in the system. An additional wire is included for adding an optional on/off solenoid to stop fluid flow when the system is inactive.

AEM’s Boost Dependent, PN 30-3300 gasoline Water/Methanol Injection System’s compact 1 gallon tank includes a high tech conductive low fluid level indicator with a positive lock connector and color matched wires to the wiring harness. AEM strongly recommends that users never exceed a 50% methanol concentration when using any AEM Water Methanol system or component.

All AEM Water/Methanol injection systems and components (pump, lines, fittings, filter, flow sensor, tank, and nozzles) are 100% chemically compatible with methanol. However, for safety reasons we strongly recommend that users never use more than a 50% methanol concentration in our systems.

Methanol is a toxic and highly flammable chemical. 100% Methanol ignites easily and burns vigorously with an almost undetectable flame. Methanol can be absorbed through the skin and even small amounts can cause blindness or even death. Using this fluid at high pressures, without dilution, in an under-hood environment with nylon lines and push-to-connect fittings is very unsafe. The performance advantages of using greater than 50% methanol concentrations are small, if they exist at all. However, the safety issues are very real and far outweigh any perceived benefit of running high concentrations of methanol.

AEM Part Numbers
V2 Water Methanol Kit With 4 Liter Tank - 30-3300 V2 Water Methanol Kit With 19 Liter Tank - 30-3301

AEM’s Water/Methanol Injection Filter can filter particulates as small as 40 microns. It protects the working parts of the water/methanol system and the engine from particulates in the water/methanol mixture when installed in-line before the water/methanol pump, and can be used on virtually any water/methanol injection system using ¼” OD tubing.

Why An Inline Filter Is A Good Idea.

If you are using a Water/Methanol Injection System it may greatly increase pump life to use a water/methanol filter. The AEM Water/Methanol Injection Filter prevents foreign particles as small as 40 microns from clogging or damaging pumps, injection nozzles check valves or flow sensors. The AEM Water/Methanol Injection Filter uses fittings for use with 1/4" OD nylon tubing, so it fits most Water/Methanol injection kits on the market today!

• Simple to install, takes less than a minute!
• Fits virtually every Water/Methanol system on the market.
• Polypropylene housing - rugged material that is compatible with high concentrations of methanol.
• Completely Serviceable Assembly - can be disassembled, cleaned and reused for a long service life.
• Stainless Steel mesh strainer - AEMs custom mesh strainer filters down to 40 microns - MUCH smaller than similar filters.
• Large Filtering Area assure long service life and does not significantly reduce flow.
• Micronic Mesh Screen out-performs sintered filters in both filtering and serviceability.

AEM PART NUMBER - 30-3003

This is a high quality replacement air filter for your RX-7 fits both RX-7 FC3s and FD3s.
A Genuine Mazda Air Filter will be supplied whenever possible, however if unavailable we may select a high quality alternative.