AEM’s Water/Methanol Injection Filter can filter particulates as small as 40 microns. It protects the working parts of the water/methanol system and the engine from particulates in the water/methanol mixture when installed in-line before the water/methanol pump, and can be used on virtually any water/methanol injection system using ¼” OD tubing.

Why An Inline Filter Is A Good Idea.

If you are using a Water/Methanol Injection System it may greatly increase pump life to use a water/methanol filter. The AEM Water/Methanol Injection Filter prevents foreign particles as small as 40 microns from clogging or damaging pumps, injection nozzles check valves or flow sensors. The AEM Water/Methanol Injection Filter uses fittings for use with 1/4″ OD nylon tubing, so it fits most Water/Methanol injection kits on the market today!

• Simple to install, takes less than a minute!
• Fits virtually every Water/Methanol system on the market.
• Polypropylene housing – rugged material that is compatible with high concentrations of methanol.
• Completely Serviceable Assembly – can be disassembled, cleaned and reused for a long service life.
• Stainless Steel mesh strainer – AEMs custom mesh strainer filters down to 40 microns – MUCH smaller than similar filters.
• Large Filtering Area assure long service life and does not significantly reduce flow.
• Micronic Mesh Screen out-performs sintered filters in both filtering and serviceability.

AEM PART NUMBER – 30-3003

Offering a discount when bought as a 4 pack, These coils are becoming increasingly popular in the RX7 FD Market.

AEM’s High-Output IGBT “Smart” Inductive Coils each deliver up to 103mJ of spark energy and a minimum of 40,000 Volts—as much as most CDI systems but without the need for a CDI module! These coils provide very long spark duration at full energy, unlike CDI systems and multiple spark systems which fire off small spark events prior to and after its CDI burst to mimic longer spark duration. The full energy delivery and long duration of AEM’s High-Output IGBT “Smart” Inductive Coils eliminate the need to compromise energy or duration with your ignition system, and will increase performance in high-boost or high compression engines.

AEM’s High-Output IGBT “Smart” Inductive Coils deliver CDI-like spark energy with the long duration of an inductive coil. They install easily in place of your exiting coils and do not require a CDI module. AEM’s High-Output IGBT “Smart” Inductive Coils have a shock and weatherproof design that allows them to be mounted virtually anywhere. And at a cost less than what you would pay for aftermarket LS1 coils—they deliver World-Class performance at a bargain. AEM’s High-Output Coils are used on 2,000-horsepower nitrous motors without a CDI, and they perform flawlessly.

TECHNICAL SPECIFICATIONS

PLEASE NOTE THESE COILS ARE NOY PLUG AND PLAY, THEY WILL REQUIRE INSTALLATION AND THE FABRICATION OF CUSTOM WIRING. IF YOUR NOT CONFIDENT TN THIS AREA WE RECOMMEND HAVING A PROFESSIONAL UNDERTAKE THE INSTALLATION.

PLEASE NOTE THIS IS A SPECIAL ORDER ITEM.

AEM PART NUMBER – 30-2853

AEM’s High-Output IGBT “Smart” Inductive Coils each deliver up to 103mJ of spark energy and a minimum of 40,000 Volts—as much as most CDI systems but without the need for a CDI module! These coils provide very long spark duration at full energy, unlike CDI systems and multiple spark systems which fire off small spark events prior to and after its CDI burst to mimic longer spark duration. The full energy delivery and long duration of AEM’s High-Output IGBT “Smart” Inductive Coils eliminate the need to compromise energy or duration with your ignition system, and will increase performance in high-boost or high compression engines.

AEM’s High-Output IGBT “Smart” Inductive Coils deliver CDI-like spark energy with the long duration of an inductive coil. They install easily in place of your exiting coils and do not require a CDI module. AEM’s High-Output IGBT “Smart” Inductive Coils have a shock and weatherproof design that allows them to be mounted virtually anywhere. And at a cost less than what you would pay for aftermarket LS1 coils—they deliver World-Class performance at a bargain. AEM’s High-Output Coils are used on 2,000-horsepower nitrous motors without a CDI, and they perform flawlessly.

TECHNICAL SPECIFICATIONS

PLEASE NOTE THESE COILS ARE NOY PLUG AND PLAY, THEY WILL REQUIRE INSTALLATION AND THE FABRICATION OF CUSTOM WIRING. IF YOUR NOT CONFIDENT TN THIS AREA WE RECOMMEND HAVING A PROFESSIONAL UNDERTAKE THE INSTALLATION.

PLEASE NOTE THIS IS A SPECIAL ORDER ITEM.

AEM PART NUMBER – 30-2835

Reduce Intake Air Temperatures and Exhaust Gas Temps, while  Increasing Octane Rating of Pump Fuel, Knock Protection. Run More Boost and Timing, Make More Power

Please select your desired tank size from the drop down menu before adding your selection to the shopping cart

Water/methanol injection for gas engines is a proven means for effectively reducing engine inlet air temperatures and suppressing harmful detonation on forced induction and high performance naturally aspirated race engines. This allows racers to reliably increase boost and advance ignition timing—without using high-octane racing fuel—for power gains of up to 20%. AEM’s Water/Methanol Injection Systems utilize the most robust hardware combined with more advanced features than any other comparably priced water/methanol system.

The on-demand progressive controller in AEM’s Boost Dependent PN30-3300 Water/Methanol Injection kit bases injection flow on manifold pressure using an on-board MAP sensor (up to 35 PSI of boost) to ensure the proper amount of water/methanol injection at all points along an engine’s power curve.

AEM’s engineers spent extensive time developing the controller’s flow control strategy for a more linear flow output delivery. This means that the flow delivery better matches an engine’s need for water/methanol injection, which further optimizes charge air cooling and detonation control.

The new controller design features large, turn-resistant knobs and larger numbering to easily set accurate start and full activation points, with covered status LED and test buttons for added splash resistance. A plug is integrated into the controller housing for mating to the redesigned wiring harness’s positive-lock connector. The Boost Dependent controller housing has a molded-in, barbed nipple to accept a boost hose and a wiring legend on the back, integrated fuse and molded mounting tabs.

AEM’s Boost Dependent Water/Methanol Injection kit’s wiring harness is terminated with a positive-lock connector on one end and has color-coded wires to ease installation. Both the power and ground wires for the pump are included in the harness which simplifies the wiring process and eliminates any chance of the pump accidentally activating from a short in the system. An additional wire is included for adding an optional on/off solenoid to stop fluid flow when the system is inactive.

AEM’s Boost Dependent, PN 30-3300 gasoline Water/Methanol Injection System’s compact 1 gallon tank includes a high tech conductive low fluid level indicator with a positive lock connector and color matched wires to the wiring harness.

AEM strongly recommends that users never exceed a 50% methanol concentration when using any AEM Water Methanol system or component.

All AEM Water/Methanol injection systems and components (pump, lines, fittings, filter, flow sensor, tank, and nozzles) are 100% chemically compatible with methanol. However, for safety reasons we strongly recommend that users never use more than a 50% methanol concentration in our systems.

Methanol is a toxic and highly flammable chemical. 100% Methanol ignites easily and burns vigorously with an almost undetectable flame. Methanol can be absorbed through the skin and even small amounts can cause blindness or even death. Using this fluid at high pressures, without dilution, in an under-hood environment with nylon lines and push-to-connect fittings is very unsafe. The performance advantages of using greater than 50% methanol concentrations are small, if they exist at all. However, the safety issues are very real and far outweigh any perceived benefit of running high concentrations of methanol.

AEM Part Numbers
V2 Water Methanol Kit With 4 Liter Tank – 30-3300
V2 Water Methanol Kit With 19 Liter Tank – 30-3301

Reduce Intake Air Temperatures and Exhaust Gas Temps, while  Increasing Octane Rating of Pump Fuel, Knock Protection. Run More Boost and Timing, Make More Power

Water/methanol injection for gas engines is a proven means for effectively reducing engine inlet air temperatures and suppressing harmful detonation on forced induction and high compression naturally aspirated (NA) race engines. This allows racers to reliably increase boost and advance ignition timing—without using high-octane racing fuel—for power gains of up to 20%. AEM’s Water/Methanol Injection Systems utilize the most robust hardware combined with more advanced features than any other comparably priced water/methanol system.

The on-demand progressive controller in AEM’s Boost Dependent PN30-3302 tank-less Water/Methanol Injection kit bases injection flow on manifold pressure using an on-board MAP sensor (up to 35 PSI of boost) to ensure the proper amount of water/methanol injection at all points along an engine’s power curve.

AEM’s engineers spent extensive time developing the controller’s flow control strategy for a more linear flow output delivery. This means that the flow delivery better matches an engine’s need for water/methanol injection, which further optimizes charge air cooling and detonation control.

The new controller design features large, turn-resistant knobs and larger numbering to easily set accurate start and full activation points, with covered status LED and test buttons for added splash resistance. A plug is integrated into the controller housing for mating to the redesigned wiring harness’s positive-lock connector. The Boost Dependent controller housing has a molded-in, barbed nipple to accept a boost hose and a wiring legend on the back, integrated fuse and molded mounting tabs.

AEM’s Boost Dependent Water/Methanol Injection kit’s wiring harness is terminated with a positive-lock connector on one end and has color-coded wires to ease installation. Both the power and ground wires for the pump are included in the harness which simplifies the wiring process and eliminates any chance of the pump accidentally activating from a short in the system. An additional wire is included for adding an optional on/off solenoid to stop fluid flow when the system is inactive.

AEM strongly recommends that users never exceed a 50% methanol concentration when using any AEM Water Methanol system or component.

All AEM Water/Methanol injection systems and components (pump, lines, fittings, filter, flow sensor, tank, and nozzles) are 100% chemically compatible with methanol. However, for safety reasons we strongly recommend that users never use more than a 50% methanol concentration in our systems.

Methanol is a toxic and highly flammable chemical. 100% Methanol ignites easily and burns vigorously with an almost undetectable flame. Methanol can be absorbed through the skin and even small amounts can cause blindness or even death. Using this fluid at high pressures, without dilution, in an under-hood environment with nylon lines and push-to-connect fittings is very unsafe. The performance advantages of using greater than 50% methanol concentrations are small, if they exist at all. However, the safety issues are very real and far outweigh any perceived benefit of running high concentrations of methanol.

AEM PART NUMBER 30-3302

If you are using a Water/Methanol Injection System and want to know exactly how much fluid you are actually injecting into your engine, the AEM Water/Methanol Flow Gauge is a must. It replaces the “dummy light” with actual data displayed on a smooth moving needle-type gauge that allows you to accurately monitor the status of your injection system in real time. The AEM Water/Methanol Flow Gauge comes with black and silver bezels and white and black faceplates for multiple color combinations.

AEM Part Number 30-5142

WHAT IT DOES

If you are using a Water/Methanol Injection System and want to know exactly how much fluid you are actually injecting into your engine, the AEM Water/Methanol Flow Gauge is a must. It replaces the “dummy light” with actual data displayed on a smooth moving needle-type gauge that allows you to accurately monitor the status of your injection system in real time. The AEM Water/Methanol Flow Gauge comes with black and silver bezels and white and black faceplates for multiple color combinations.

The gauge kit includes a precision flow sensor and fittings for use with 1/4″ OD nylon tubing, so the AEM Water/Methanol Flow Gauge fits most Water/Methanol injection kits on the market today.

For best results the 0-1000CC Flow Gauge (AEM part# 30-5142) should be used on Water/Methanol kits injecting more than 500 cc/min and is ideal for those with the AEM Water/Methanol kit using the largest size or multiple sized nozzles. If you are using only a small or medium AEM nozzle, we suggest the 0-500CC Flow Gauge (AEM part# 30-5141)

WHY YOU WANT ONE

AEM’s Water/Methanol Gauge gives you the exact amount of water/methanol you are spraying into your engine. Boost with the extra confidence of knowing your flow though your entire RPM and boost range. The gauge comes with both a white and black face place to perfectly match your interior.

PRODUCT FEATURES

• Gauge Readout from 0 to 1000cc
• Adjustable backlighting via a dial on the back of the gauge
• Includes black and silver interchangeable bezels and white and black faceplates
• 320 degree viewing area for unsurpassed resolution
• Fits virtually every water/methanol kit on the market today!
• 0-5v analog output included for use with data loggers and virtually any engine management system

Special Order Item Only.

Replacement Air Filter for your RX-8 AEM Induction Kit.

• Designed to increase horsepower and throttle response
• AEM Air Filters are cleanable and reusable for the life of your vehicle
• Captures up to 99% of harmful contaminants
• Outstanding performance even in dusty racing conditions
• Manufactured in the USA
• Does not require oil
• Will NOT void vehicle warranty
• Guaranteed for the life of your vehicle

AEM Dryflow Air Filters are washable synthetic air filters designed for an optimum combination of air flow, filtration, and performance. AEM Dryflow filters use an innovative high performance oil-free filtration material that allows easy cleaning, durable service, and excellent filtration. Replacement air filters for street vehicles come with a lifetime limited warranty. Other air filters come with a one year limited warranty.

Replacement Pre-filter “Sock” for your AEM Intake Filter

• Made of a durable micro-screen material
• Protects your Dryflow air filter from water and mud
• Also blocks small dirt particles
• Adds very little air restriction

AEM Dryflow Pre-Filters are manufactured from a durable micro-screen material and pre-treated with a proprietary hydrophobic process designed to prevent splashes of water or mud from saturating your Dryflow air filter. AEM Dryflow Pre-filters also stop small dirt particles; yet add little restriction.

The ever popular AEM induction Kit for the RX-8 is a True Cold Air Intake meaning the filter is actually positioned in the mouth of the car low down where air passes over it before passing over the radiators.

Easy to install without the need for inner wheel well cutting or modification.
The filter element with built-in velocity stack is especially designed to create a massive increase in air flow capacity.

This Kit uses to OEM style mesh screens in the intake to prevent poor idle that is quite common on many other “cheap” induction systems. equipped with a special K&N cone filter and water “resistant sock” this kit is a lot louder then the Racing Beat kit we also offer.

Avilable in:

• Red
• Blue
• Chrome
• Grey
• Polished

Please Allow 7-14 Days for Delivery when not in stock.