Normal Price £350.00

Add 50mm to each side of your RX-7 FC’s front end. Super deep dish wheels are now possible.
This is a brand new part to the UK and has never been available before brought to you by Essex Rotary. Up till now the largest available from a UK seller has been +30mm each side. Our new Fibreglass Over Fenders add a massive 50mm extra to each side , giving your FC3s a wide aggressive look. These are made here in the UK for Essex Rotary using high quality British fibreglass and finished in flexible white gelcoat, with out signature Essex Rotary Green finish on the inside. Made to a high standard so fit to your car will not be a problem, saving you time, money and headache. No one likes a bad fitting part.

Thin But Strong
Our new Super Wide Over Fenders are made thin enough to be flexible, this helps with fitting and conforming to the shape of your RX-7 while remaining thick enough to be strong. You will get 1 set (one left and one right) front over fender.

While DIY Installation is possible, Essex Rotary recommend installation be carried out by a professional, Always test fit fibreglass parts and trim (if required) to your preference prior to painting.

Weighing in at 13.05kg total for the entire assembly.

The CCI twin disc provides the most economical racing clutch for the active sport compact enthusiast. This ceramic twin disc comes with a 4140 forged flywheel and a 6061 T6 aluminium cover complimented with a 6150 steel diaphragm. These units are rated to hold 500 to 1200hp (depending on application).

Competition Clutch Part Number 4-10037-C

This Kit includes Twin Plate Clutch and Flywheel.

Essex Rotary would recommend changing your pilot bearing and seal out at the same time as doing your clutch, this is an inexpensive part however its often overlooked when doing the job.

This Kit will not fit the Non Turbo (EGI) RX-7 FC. Please contact us for Info on EGI Clutches.

6 Pad Sprung Ceramic Kit good for up to 600hp.

Stage 4 – Spring Strip Series 1620 Clutch Kit.

This assembly, available with a six puck sprung plate is good for penetrating engagement with higher horsepower applications. This disc complimented by a performance pressure plate provides up to 250% increase in torque capacity. 300-mile break-in recommended with this set-up.

The 1620 Series kit includes a performance pressure plate, a six-puck high torque sprung disc with Ceramic buttons, all applicable bearings, and the appropriate alignment tool.

Please note that the images provided are for illustration purposes only and the clutch kit supplied WILL be the pull type correct for the RX-7 FD transmission.

Essex Rotary would recommend changing your pilot bearing and seal out at the same time as doing your clutch, this is an inexpensive part however its often overlooked when doing the job.

This Kit will not fit the Non Turbo (EGI) RX-7 FC. Please contact us for Info on EGI Clutches.

Sprung Segmented Ceramic, Good for up to 525hp

Stage 3 – Street / Strip Series 2600 Clutch Kit.

Great for heavily modified Forced Induction RX-8′s but keeps a streetable clutch pedal feel
This segmented Ceramic material with a performance pressure plate will provide the ultimate in street and strip combinations. This assembly is suited for up to 150% increase in torque capacity. Provides quick but smooth engagement and extended life. 300-mile break-in recommended with this set-up.

The 2600 Series kit includes a performance pressure plate, a high torque sprung disc with segmented Ceramic facings, all applicable bearings, and the appropriate alignment tool.

Please note that the images provided are for illustration purposes only and the clutch kit supplied WILL be the pull type correct for the RX-7 FD transmission.

Essex Rotary would recommend changing your pilot bearing and seal out at the same time as doing your clutch, this is an inexpensive part however its often overlooked when doing the job.

This Kit will not fit the Non Turbo (EGI) RX-7 FC. Please contact us for Info on EGI Clutches.

Stage 2 – Steel Sprungback Brass Plus.
Street /Track Series 2100 Clutch Kit, Rated for handling up to 450hp
A great priced option for street use while still being extremely capable on the track.

This assembly provides up to 80% increase in torque capacity and is properly suited for aggressive street use and moderate track use. The Brass Plus material with its alloy backing matched to a performance pressure plate will provide smooth engagement and extended life. 500 mile break-in highly recommended with this set-up. 300-mile break-in REQUIRED with this set-up. (Some kits may not be supplied with all pieces. Please verify with Competition Clutch before ordering).

The 2100 Series kit includes a performance pressure plate, a high torque sprung disc with anti-burst steel backed Brass Plus facings, all applicable bearings, and the appropriate alignment.
Please note that the images prodided are for illustration purposes only and the clutch kit supplied WILL be the pull type correct for the RX-7 FD transmission.

Essex Rotary would recommend changing your pilot bearing and seal out at the same time as doing your clutch, this is an inexpensive part however its often overlooked when doing the job.

This Kit will not fit the Non Turbo (EGI) RX-7 FC. Please contact us for Info on EGI Clutches.

This product is one of Adaptonic’s plug-in ECUs, also called eMod009. It’s a direct plug and play for S4 Mazda RX7 FC.

Our main objective in creating the Adaptronic Modular ECU line is to work towards Adaptronic’s mission which is to give people control. In doing this, we came up with a system which would give people greater flexibility and at the same time, overcome the limitations of our main product line, the Select ECU’s.

GENERAL FEATURES

• Modular system, so that people can buy hardware upgrades later as their needs develop (eg additional inputs, outputs, or specific functions, eg drive by wire or built-in lambda)
• Offer a waterproof option, using Superseal connectors
• Wireless communication
• Fast USB communication, requiring no drivers
• Headphone port for listening to the knock sensor while tuning
• 4 x serial in ports
• 1 x CAN port
• Power over USB to do loading of maps, firmware etc without having to provide it with 12V power
• 32MB of onboard logging to flash
• Exception logging, able to detect faults and log a bunch of things that happen around the same time to help with ECU setup and tech support
• Bigger maps, more of them, and more dedicated maps.
• Tested to MIL-STD-202G, a military vibration standard, which varies the frequency and peaks at 7.5g of oscillating acceleration

This product is one of Adaptonic’s plug-in ECUs. Also called RX7 S5.

Our main objective in creating the Adaptronic Modular ECU line is to work towards Adaptronic’s mission which is to give people control. In doing this, we came up with a system which would give people greater flexibility and at the same time, overcome the limitations of our main product line, the Select ECU’s.

GENERAL FEATURES

• Modular system, so that people can buy hardware upgrades later as their needs develop (eg additional inputs, outputs, or specific functions, eg drive by wire or built-in lambda)
• Wireless communication
• Maximum output of 22 (8 ignition, 8 injector, 4 auxiliary, tacho and fuel pump)
• 3 complementary drivers in the ECU to drive inverse outputs
• Smooth transition to direct fire
• Drive dual speed fuel pump
• Injector staging is automated
• Has an option to manually set the percentage of fuel to be delivered in secondary (or third, or fourth…) stages
• Handle the factory pickup, the 36-1 FFE trigger with the factory sensor, and the 36-1 FFE trigger with a Hall effect sensor
• Fast USB communication, requiring no drivers
• Headphone port for listening to the knock sensor while tuning
• 4 x serial in ports
• 1 x CAN port
• Power over USB to do loading of maps, firmware etc without having to provide it with 12V power
• 32MB of onboard logging to flash
• Exception logging, able to detect faults and log a bunch of things that happen around the same time to help with ECU setup and tech support
• Tested to MIL-STD-202G, a military vibration standard, which varies the frequency and peaks at 7.5g of oscillating acceleration

This ECU plugs directly into the factory loom, with additional inputs and outputs available on unused pins in the factory connector. The additional pins you have access to give you the following options:

• • • An additional 2 injector outputs
    • An additional O2 input, and 2 additional 0-5V inputs for logging or other functions like sequential box strain gauges
    • Additional ignition output for conversion to direct fire
    • Oil pressure, fuel pressure and oil temperature inputs (plus we read the fuel temperature input and use that in the fuel density calculation)
    • CAN (Wideband lambda can be connected via analogue input, or via serial.)

Normal Price £250.00

Add 50mm to each side of your RX-7 FC’s rear end. Super deep dish wheels are not possible

This is a brand new part to the UK and has never been available before brought to you by Essex Rotary.

Up till now the largest available from a UK seller has been +30mm each side.

Our new Fibreglass Over Fenders add a massive 50mm extra to each side , giving your FC3s a wide aggressive look.

These are made here in the UK for Essex Rotary using high quality British fibreglass and finished in flexible white gelcoat. with out signature Essex Rotary Green finish on the inside.

Made to a high standard so fit to your car will not be a problem, saving you time, money and headache.

No one like a bad fitting part.

Thin But Strong

Our new Super Wide Over Fenders are made thin enough to be flexible, this helps with fitting and conforming to the shape of your RX-7 while remaining thick enough to be strong.

You will get 1 set (one left and one right) rear over fender, please note this kit does not include a fuel filler cap extension.

Essex Rotary recommend installation be carried out by a professional, Always test fit fibreglass parts and trim (if required) to your preference prior to painting.

Comma 15w40 Mineral Oil 4 x 5 Liter (20 Liters total) Pack offering a big saving on shipping costs.

This is the standard stuff that we normally use on our services, offering a higher viscosity than the recommended oil, 15w40 will help protect the inside of your engine better especially the stationary gear bearings (a key weak point on the RX-8 when using 5w30)

This oil is supplied in a 5 liter can and should be enough for a oil change plug 1-1.5 liters spare for top ups.

We recommend 3000-6000mile (or 6 months) oil changes to keep your oil as clean as possible.

Larger quantities are available please contact us for pricing

Made to order, right here at Essex Rotary using all MSD Components.

The MSD 8.5 mm Super Conductor wire is the performance wire engineered from the inside out, the 8.5mm offers everything you have ever wanted in a wire; incredibly low resistance without electronic interference! In a single 12 In. length of Super Conductor wire there is only 40 to 50 ohms of resistance! That is the lowest resistance of any helically wound wire. To accomplish this, MSD use a copper alloy conductor due to it’s great voltage carrying capabilities. The low resistance results in less loss of spark energy so more reaches the spark plug. The conductor is wound extremely tight around a special center core. So tight, that there is over 40 Ft. of conductor wrapped into a single foot of plug wire. This winding procedure, combined with a ferro-magnetic impregnated center core, produces an extremely effective electro magnetic interference (EMI) choke.

• Copper alloy conductor has a resistance value of less than 50 ohms per foot for superior spark
• Ferro-magnetic impregnated core creates an effective EMI choke
• Forty feet of conductor is wound into a single foot of wire for high EMI suppression
• Conductor core features Dupont Kevlar material for increased tensile strength
• Durable outer sleeve is a proprietary compound for resistance to high heat or abrasion
• Stainless steel terminals feature dual crimp tabs to grip wire conductor and outer jacket separately

These MSD HT Leads are made to order right here at Essex Rotary HQ, from genuine MSD components. Available in Red or Black cable options (select your preferred color from the drop down menu before hitting the “add to cart” button.

Custom lengths and configurations available upon request.

This Kit contains everything you will need to carry out the conversion from conventional coolant over to Evans Waterless Coolant on your Mazda RX-7 or RX-8.

Plus we are offering  5% Discount when purchasing this pack compared to purchasing everything individually.

This Kit Contains the following;

• 2 x 5 Litre bottles of Evans Prep Fluid.
• 2 x 5 Litre bottles of Evans Power Cool 180 Waterless Coolant.

This is the perfect starter pack to carry our a full conversion offered with a great bulk shipping discount.

Before using Evans Waterless coolant for the first time it is advised that Evans Prep fluid is used to flush the cooling system of ay remaining water based coolant, This is essential for a successful conversion to Evans Waterless coolant.

For more information on Prep Fluid and Power Cool 180 can be found in their individual product descriptions above.

Evans Prep Fluid MUST be used before Evans coolant is installed in your cooling system for the first time, when converting from traditional coolant.

Evans Prep Fluid is specifically formulated to hygroscopically absorb any water-based coolant remaining in the cooling system after initial drain. Because certain parts of the cooling system might not drain out with gravity, and it would take too long to disconnect every pipe etc., installing a scavenging fluid is the most practical method of removing all the water-based coolant.

The Prep Fluid is not formulated to chemically clean the engine of rust and scale, but the process of circulation and draining will help remove any loose sediment.

Evans Prep Fluid must be used before converting from a water based coolant to Evans Waterless Engine Coolant.

2 x 5 Litre cans will be required to fill a full cooling system of most RX-7′s or RX-8′s
We are offering a Discounts for 2 bottle packs plus combined delivery discount if buying two bottles together to be shipped to a UK Mainland address, Simply select your desired quantity from the drop down menu.

Evans Power Cool 180 is the coolant of choice for many professional racing teams and performance car specialists. For use in all performance car engines primarily fabricated from aluminium, plus some steel and copper components.

Conversion from a water-based coolant to Evans is a straight forward process that can be undertaken by anyone with some basic experience in engine mechanics.

The primary objective of converting to Evans Waterless Engine Coolant is to eliminate all of the problems associated to water:

Eliminates Overheating
Evans Waterless Coolants have a boiling point above 180°C and will not vaporise, thus eliminating overheating, boil-over and after-boil.

Reduces Pressure
Evans Waterless Coolants generate very low vapour pressures reducing strain on engine hoses and cooling system components.

Prevents Corrosion
Water promotes corrosion via oxidation and electrolysis. Evans Waterless Coolants contain no oxygen and are virtually non-conductive effectively preventing corrosion.

Maximise BHP
Evans Waterless Coolants eliminate pre-ignition and detonation caused by overheating – thus increasing combustion efficiency and delivering more power.

Stops Erosion
Evans Waterless Coolants stop cavitation and eliminate liner and cooling pump erosion.

Freeze Protection
Evans Waterless Coolants freeze below -40ºC

Non-Toxic
Evans Waterless Coolants are proven to be Non-Toxic. Standard anti-freeze is toxic and known to kill pets.

If the engine to be converted is currently filled with a water-based coolant an important part of a good installation is using Evans Prep Fluid. Prep Fluid is specifically formulated to purge remaining water-based antifreeze from the system after initial drain. Evans Prep Fluid is sold separately and available just below.

2 x 5 Litre cans will be required to fill a full cooling system of most RX-7′s or RX-8′s
We are offering a Discounts for 2 bottle packs plus combined delivery discount if buying two bottles together to be shipped to a UK Mainland address, Simply select your desired quantity from the drop down menu.

This is a high quality replacement air filter for your RX-7 fits both RX-7 FC3s and FD3s.
A Genuine Mazda Air Filter will be supplied whenever possible, however if unavailable we may select a high quality alternative.

High Quality Replacement Clutch Slave Cylinder for the Mazda RX-7 FC3s This will fit the 2nd Generation RX-7 Turbo II Only
Many owners are choosing to replace their clutch Master and Slave Cylinder as a precautionary measure, There is nothing worse then a brake down due to a leak on either of these cylinders.

Common signs of slave cylinder failure include

• The Pedal failing to return to the top when released
• Clutch fluid leaking from the Cylinder
• Inability to select gears

This is the Master Cylinder you will require if your using a Turbo II Gearbox in your RX-7, it is worth noting that this is different to the EGI Slave cylinder.

An excellent upgrade for your old, tired or failed ignition coils in your RX-7 FB or FC ECI. These MSD coils offer very high voltage output of up to 45’000 volts.

MSD ignition Coil, Blaster 2, with Ballast and Hardware

Blaster 2 Coil, w/Ballast & Hardware

If you are looking to upgrade your stock coil or want to complement the performance of your MSD 6-Series Ignitions, our blaster coils are the right choice. For MSD Ignition applications. With a stock points style ignition, a ballast resistor must be placed in-line with the positive terminal of the coil. These blaster coils are supplied with a 0.8 ohm ballast resistor plus a terminal and boot to fit most applications. Mallory Melonite applications also require the ballast resistor.

• Performance upgrade for canister style coils
• High voltage and energy output
• Improved materials and turns ratio
• Improved performance
• A performance upgrade for points
• Comes with 0.8 ohm resistor; fits most applications
• CARB approved legal for use in all states
• Use with stock or MSD 6-Series Ignitions

A great upgrade option for your failed OEM coils on an early rotary engine.

MSD ignition Coil, Blaster 2, High Performance

Blaster 2 Coil

The blaster coils share the same special windings and high voltage output but do not include a ballast resistor.
When you are using an MSD Ignition control, the ignition is responsible for delivering the voltage to the coil so a ballast resistor is not necessary.

• Low resistance and improved turns ratio produces a powerful spark for improved performance
• Special windings and high voltage output; does not include a ballast resistor
• Sturdy metal housing is finished in red
• OBD II and CARB approved; legal for use in all states; D-40-37

Essex Rotary can now offer the popular K-Sport range of AirRide suspension for your RX-7 or RX-8.

Air suspension Deluxe system improves on the Basic kit by adding several upgrades. One Air Zenith compressors are included which fill the tank twice as fast as the Basic kit. We include two electronic switches (front/rear and up/down) which offer more precise control over manual paddle valves and thanks to our seamless installation system, all the electronics are housed in a stylish red and black control box. A 200 PSI dual needle gauge is included as well. All you need to do is run 2 air lines to the control box, one from the box to the tank and complete your wiring via the quick disconnect plug on the right side of the box and you’re up and running. A wireless remote control is also included so you can operate the system from outside the vehicle if you wish.

Professional installation is recommended.

All Ksport Airtech air suspension systems feature high quality air bags, proven to handle the stress and abuse of daily driving as well as drift circuit use. Take advantage of the near infinite adjustability thanks to the adjustable lower mount, 36 levels of damping adjustment, and the unmatched height adjustability (0-120/200mm depending on vehicle) of air suspension.

These air suspension kits are designed for easy bolt-on installation.

No modifications to OEM shock absorbers, or OEM top mounts is required.

Vehicle may need to be modified for air line routing.

All Ksport Airtech Systems use Air Zenith compressors, and can be raised from the lowest setting to max height in as little as 2 seconds.

All Hoses, wiring, and installation manuals are included.

Features Include:

• 5 Gallon Air Tank with Carpeted Mounting Board
• Manual paddle valves & 200 PSI dual needle gauge
• Air Zenith air compressor
• Wide Range Height Adjustability
• High Pressure Air Bags
• High Performance Ksport Shock Absorbers
• Adjustable Lower Mount
• 36 Way Adjustable Damping

5 gallon air tank w/carpeted mounting board
A standard black steel air tank is included with the Basic and Deluxe kits.

Manual paddle valves & 200 PSI dual needle gauge
Manual paddle valves offer control of front and rear air bags. 200 psi dual needle gauge included along with mounting bracket for a clean install.

Ksport seamless installation
Our control unit offers as simple an installation as possible. Simply run your air lines to the box and connect 4 wires to our quick disconnect plug, wire up the compressors and relay and you’re done.

Remote control
Adjust your ride height from outside your car with the included basic wireless remote control.

Air Zenith air compressor
Basic kits come with a single Air Zenith compressor. We chose to use Air Zenith compressors for their reliability and performance.

Wide Range Height Adjustability
Range of lowering is 0 to 120/200mm depending on vehicle.

High Pressure Air Bags
Engineered and designed to match your vehicle. Sleeve type and double bellow type bags are available depending on what type of OEM suspension your vehicle has. Air pressure directly corresponds with how stiff or soft your car rides. Higher PSI = stiffer ride. Lower PSI = softer ride. Each car is different and it may take some time to dial in your preferred settings

High Performance KSport Shock Absorbers
Every air kit comes with the same quality shocks that are standard in our control Pro coilover systems. Air kit shocks have a different internal valving setting to accommodate changes in PSI.

Adjustable Lower Mount
Adding further fine tuning of your ride height at any PSI setting you chose is the ability to have an adjustable lower mount just like our coilover kits. The benefit to this is being able to get the perfect ride height at basically any PSI you are comfortable driving at

6 Way Adjustable Damping
All Ksport AirTech systems offer 36 levels of damping which allow you the ability to dial in your air suspension even further. Set damping softer (counterclockwise) or stiffer (clockwise) by simply inserting the included damping knob and turning it either way.

This Item is special order only and is subject to our special order T&C’s please read these before finalising your payment a link to our T&C’s can be found on the checkout page below the shopping cart.

Essex Rotary can now offer the popular K-Sport range of AirRide suspension for your RX-7 or RX-8.

Air Suspension K-sport Basic system is for people who want a complete bare bones direct bolt in air suspension system. This system features a manual paddle valve system with basic front and rear up/down operation from the switch panel that is included. A 200 PSI dual needle gauge is mounted right next to the switches so you can easily see where your air pressure is at all times. One Air Zenith compressor is standard along with our 5 gallon black steel air tank.

Professional installation is recommended.

All Ksport Airtech air suspension systems feature high quality air bags, proven to handle the stress and abuse of daily driving as well as drift circuit use. Take advantage of the near infinite adjustability thanks to the adjustable lower mount, 36 levels of damping adjustment, and the unmatched height adjustability (0-120/200mm depending on vehicle) of air suspension.

These air suspension kits are designed for easy bolt-on installation.

No modifications to OEM shock absorbers, or OEM top mounts is required.

Vehicle may need to be modified for air line routing.

All Ksport Airtech Systems use Air Zenith compressors, and can be raised from the lowest setting to max height in as little as 2 seconds.

All Hoses, wiring, and installation manuals are included.

Features Include:

• 5 Gallon Air Tank with Carpeted Mounting Board
• Manual paddle valves & 200 PSI dual needle gauge
• Air Zenith air compressor
• Wide Range Height Adjustability
• High Pressure Air Bags
• High Performance Ksport Shock Absorbers
• Adjustable Lower Mount
• 36 Way Adjustable Damping

5 gallon air tank w/carpeted mounting board
A standard black steel air tank is included with the Basic and Deluxe kits.

Manual paddle valves & 200 PSI dual needle gauge
Manual paddle valves offer control of front and rear air bags. 200 psi dual needle gauge included along with mounting bracket for a clean install.

Air Zenith air compressor
Basic kits come with a single Air Zenith compressor. We chose to use Air Zenith compressors for their reliability and performance.

Wide Range Height Adjustability
Range of lowering is 0 to 120/200mm depending on vehicle.

High Pressure Air Bags
Engineered and designed to match your vehicle. Sleeve type and double bellow type bags are available depending on what type of OEM suspension your vehicle has. Air pressure directly corresponds with how stiff or soft your car rides. Higher PSI = stiffer ride. Lower PSI = softer ride. Each car is different and it may take some time to dial in your preferred settings

High Performance KSport Shock Absorbers
Every air kit comes with the same quality shocks that are standard in our control Pro coilover systems. Air kit shocks have a different internal valving setting to accommodate changes in PSI.

Adjustable Lower Mount
Adding further fine tuning of your ride height at any PSI setting you chose is the ability to have an adjustable lower mount just like our coilover kits. The benefit to this is being able to get the perfect ride height at basically any PSI you are comfortable driving at

6 Way Adjustable Damping
All Ksport AirTech systems offer 36 levels of damping which allow you the ability to dial in your air suspension even further. Set damping softer (counterclockwise) or stiffer (clockwise) by simply inserting the included damping knob and turning it either way.

This Item is special order only and is subject to our special order T&C’s please read these before finalising your payment a link to our T&C’s can be found on the checkout page below the shopping cart.

AEM’s Water/Methanol Injection Filter can filter particulates as small as 40 microns. It protects the working parts of the water/methanol system and the engine from particulates in the water/methanol mixture when installed in-line before the water/methanol pump, and can be used on virtually any water/methanol injection system using ¼” OD tubing.

Why An Inline Filter Is A Good Idea.

If you are using a Water/Methanol Injection System it may greatly increase pump life to use a water/methanol filter. The AEM Water/Methanol Injection Filter prevents foreign particles as small as 40 microns from clogging or damaging pumps, injection nozzles check valves or flow sensors. The AEM Water/Methanol Injection Filter uses fittings for use with 1/4″ OD nylon tubing, so it fits most Water/Methanol injection kits on the market today!

• Simple to install, takes less than a minute!
• Fits virtually every Water/Methanol system on the market.
• Polypropylene housing – rugged material that is compatible with high concentrations of methanol.
• Completely Serviceable Assembly – can be disassembled, cleaned and reused for a long service life.
• Stainless Steel mesh strainer – AEMs custom mesh strainer filters down to 40 microns – MUCH smaller than similar filters.
• Large Filtering Area assure long service life and does not significantly reduce flow.
• Micronic Mesh Screen out-performs sintered filters in both filtering and serviceability.

AEM PART NUMBER – 30-3003

Offering a discount when bought as a 4 pack, These coils are becoming increasingly popular in the RX7 FD Market.

AEM’s High-Output IGBT “Smart” Inductive Coils each deliver up to 103mJ of spark energy and a minimum of 40,000 Volts—as much as most CDI systems but without the need for a CDI module! These coils provide very long spark duration at full energy, unlike CDI systems and multiple spark systems which fire off small spark events prior to and after its CDI burst to mimic longer spark duration. The full energy delivery and long duration of AEM’s High-Output IGBT “Smart” Inductive Coils eliminate the need to compromise energy or duration with your ignition system, and will increase performance in high-boost or high compression engines.

AEM’s High-Output IGBT “Smart” Inductive Coils deliver CDI-like spark energy with the long duration of an inductive coil. They install easily in place of your exiting coils and do not require a CDI module. AEM’s High-Output IGBT “Smart” Inductive Coils have a shock and weatherproof design that allows them to be mounted virtually anywhere. And at a cost less than what you would pay for aftermarket LS1 coils—they deliver World-Class performance at a bargain. AEM’s High-Output Coils are used on 2,000-horsepower nitrous motors without a CDI, and they perform flawlessly.

TECHNICAL SPECIFICATIONS

PLEASE NOTE THESE COILS ARE NOY PLUG AND PLAY, THEY WILL REQUIRE INSTALLATION AND THE FABRICATION OF CUSTOM WIRING. IF YOUR NOT CONFIDENT TN THIS AREA WE RECOMMEND HAVING A PROFESSIONAL UNDERTAKE THE INSTALLATION.

PLEASE NOTE THIS IS A SPECIAL ORDER ITEM.

AEM PART NUMBER – 30-2853

AEM’s High-Output IGBT “Smart” Inductive Coils each deliver up to 103mJ of spark energy and a minimum of 40,000 Volts—as much as most CDI systems but without the need for a CDI module! These coils provide very long spark duration at full energy, unlike CDI systems and multiple spark systems which fire off small spark events prior to and after its CDI burst to mimic longer spark duration. The full energy delivery and long duration of AEM’s High-Output IGBT “Smart” Inductive Coils eliminate the need to compromise energy or duration with your ignition system, and will increase performance in high-boost or high compression engines.

AEM’s High-Output IGBT “Smart” Inductive Coils deliver CDI-like spark energy with the long duration of an inductive coil. They install easily in place of your exiting coils and do not require a CDI module. AEM’s High-Output IGBT “Smart” Inductive Coils have a shock and weatherproof design that allows them to be mounted virtually anywhere. And at a cost less than what you would pay for aftermarket LS1 coils—they deliver World-Class performance at a bargain. AEM’s High-Output Coils are used on 2,000-horsepower nitrous motors without a CDI, and they perform flawlessly.

TECHNICAL SPECIFICATIONS

PLEASE NOTE THESE COILS ARE NOY PLUG AND PLAY, THEY WILL REQUIRE INSTALLATION AND THE FABRICATION OF CUSTOM WIRING. IF YOUR NOT CONFIDENT TN THIS AREA WE RECOMMEND HAVING A PROFESSIONAL UNDERTAKE THE INSTALLATION.

PLEASE NOTE THIS IS A SPECIAL ORDER ITEM.

AEM PART NUMBER – 30-2835

Reduce Intake Air Temperatures and Exhaust Gas Temps, while  Increasing Octane Rating of Pump Fuel, Knock Protection. Run More Boost and Timing, Make More Power

Please select your desired tank size from the drop down menu before adding your selection to the shopping cart

Water/methanol injection for gas engines is a proven means for effectively reducing engine inlet air temperatures and suppressing harmful detonation on forced induction and high performance naturally aspirated race engines. This allows racers to reliably increase boost and advance ignition timing—without using high-octane racing fuel—for power gains of up to 20%. AEM’s Water/Methanol Injection Systems utilize the most robust hardware combined with more advanced features than any other comparably priced water/methanol system.

The on-demand progressive controller in AEM’s Boost Dependent PN30-3300 Water/Methanol Injection kit bases injection flow on manifold pressure using an on-board MAP sensor (up to 35 PSI of boost) to ensure the proper amount of water/methanol injection at all points along an engine’s power curve.

AEM’s engineers spent extensive time developing the controller’s flow control strategy for a more linear flow output delivery. This means that the flow delivery better matches an engine’s need for water/methanol injection, which further optimizes charge air cooling and detonation control.

The new controller design features large, turn-resistant knobs and larger numbering to easily set accurate start and full activation points, with covered status LED and test buttons for added splash resistance. A plug is integrated into the controller housing for mating to the redesigned wiring harness’s positive-lock connector. The Boost Dependent controller housing has a molded-in, barbed nipple to accept a boost hose and a wiring legend on the back, integrated fuse and molded mounting tabs.

AEM’s Boost Dependent Water/Methanol Injection kit’s wiring harness is terminated with a positive-lock connector on one end and has color-coded wires to ease installation. Both the power and ground wires for the pump are included in the harness which simplifies the wiring process and eliminates any chance of the pump accidentally activating from a short in the system. An additional wire is included for adding an optional on/off solenoid to stop fluid flow when the system is inactive.

AEM’s Boost Dependent, PN 30-3300 gasoline Water/Methanol Injection System’s compact 1 gallon tank includes a high tech conductive low fluid level indicator with a positive lock connector and color matched wires to the wiring harness.

AEM strongly recommends that users never exceed a 50% methanol concentration when using any AEM Water Methanol system or component.

All AEM Water/Methanol injection systems and components (pump, lines, fittings, filter, flow sensor, tank, and nozzles) are 100% chemically compatible with methanol. However, for safety reasons we strongly recommend that users never use more than a 50% methanol concentration in our systems.

Methanol is a toxic and highly flammable chemical. 100% Methanol ignites easily and burns vigorously with an almost undetectable flame. Methanol can be absorbed through the skin and even small amounts can cause blindness or even death. Using this fluid at high pressures, without dilution, in an under-hood environment with nylon lines and push-to-connect fittings is very unsafe. The performance advantages of using greater than 50% methanol concentrations are small, if they exist at all. However, the safety issues are very real and far outweigh any perceived benefit of running high concentrations of methanol.

AEM Part Numbers
V2 Water Methanol Kit With 4 Liter Tank – 30-3300
V2 Water Methanol Kit With 19 Liter Tank – 30-3301

Reduce Intake Air Temperatures and Exhaust Gas Temps, while  Increasing Octane Rating of Pump Fuel, Knock Protection. Run More Boost and Timing, Make More Power

Water/methanol injection for gas engines is a proven means for effectively reducing engine inlet air temperatures and suppressing harmful detonation on forced induction and high compression naturally aspirated (NA) race engines. This allows racers to reliably increase boost and advance ignition timing—without using high-octane racing fuel—for power gains of up to 20%. AEM’s Water/Methanol Injection Systems utilize the most robust hardware combined with more advanced features than any other comparably priced water/methanol system.

The on-demand progressive controller in AEM’s Boost Dependent PN30-3302 tank-less Water/Methanol Injection kit bases injection flow on manifold pressure using an on-board MAP sensor (up to 35 PSI of boost) to ensure the proper amount of water/methanol injection at all points along an engine’s power curve.

AEM’s engineers spent extensive time developing the controller’s flow control strategy for a more linear flow output delivery. This means that the flow delivery better matches an engine’s need for water/methanol injection, which further optimizes charge air cooling and detonation control.

The new controller design features large, turn-resistant knobs and larger numbering to easily set accurate start and full activation points, with covered status LED and test buttons for added splash resistance. A plug is integrated into the controller housing for mating to the redesigned wiring harness’s positive-lock connector. The Boost Dependent controller housing has a molded-in, barbed nipple to accept a boost hose and a wiring legend on the back, integrated fuse and molded mounting tabs.

AEM’s Boost Dependent Water/Methanol Injection kit’s wiring harness is terminated with a positive-lock connector on one end and has color-coded wires to ease installation. Both the power and ground wires for the pump are included in the harness which simplifies the wiring process and eliminates any chance of the pump accidentally activating from a short in the system. An additional wire is included for adding an optional on/off solenoid to stop fluid flow when the system is inactive.

AEM strongly recommends that users never exceed a 50% methanol concentration when using any AEM Water Methanol system or component.

All AEM Water/Methanol injection systems and components (pump, lines, fittings, filter, flow sensor, tank, and nozzles) are 100% chemically compatible with methanol. However, for safety reasons we strongly recommend that users never use more than a 50% methanol concentration in our systems.

Methanol is a toxic and highly flammable chemical. 100% Methanol ignites easily and burns vigorously with an almost undetectable flame. Methanol can be absorbed through the skin and even small amounts can cause blindness or even death. Using this fluid at high pressures, without dilution, in an under-hood environment with nylon lines and push-to-connect fittings is very unsafe. The performance advantages of using greater than 50% methanol concentrations are small, if they exist at all. However, the safety issues are very real and far outweigh any perceived benefit of running high concentrations of methanol.

AEM PART NUMBER 30-3302

If you are using a Water/Methanol Injection System and want to know exactly how much fluid you are actually injecting into your engine, the AEM Water/Methanol Flow Gauge is a must. It replaces the “dummy light” with actual data displayed on a smooth moving needle-type gauge that allows you to accurately monitor the status of your injection system in real time. The AEM Water/Methanol Flow Gauge comes with black and silver bezels and white and black faceplates for multiple color combinations.

AEM Part Number 30-5142

WHAT IT DOES

If you are using a Water/Methanol Injection System and want to know exactly how much fluid you are actually injecting into your engine, the AEM Water/Methanol Flow Gauge is a must. It replaces the “dummy light” with actual data displayed on a smooth moving needle-type gauge that allows you to accurately monitor the status of your injection system in real time. The AEM Water/Methanol Flow Gauge comes with black and silver bezels and white and black faceplates for multiple color combinations.

The gauge kit includes a precision flow sensor and fittings for use with 1/4″ OD nylon tubing, so the AEM Water/Methanol Flow Gauge fits most Water/Methanol injection kits on the market today.

For best results the 0-1000CC Flow Gauge (AEM part# 30-5142) should be used on Water/Methanol kits injecting more than 500 cc/min and is ideal for those with the AEM Water/Methanol kit using the largest size or multiple sized nozzles. If you are using only a small or medium AEM nozzle, we suggest the 0-500CC Flow Gauge (AEM part# 30-5141)

WHY YOU WANT ONE

AEM’s Water/Methanol Gauge gives you the exact amount of water/methanol you are spraying into your engine. Boost with the extra confidence of knowing your flow though your entire RPM and boost range. The gauge comes with both a white and black face place to perfectly match your interior.

PRODUCT FEATURES

• Gauge Readout from 0 to 1000cc
• Adjustable backlighting via a dial on the back of the gauge
• Includes black and silver interchangeable bezels and white and black faceplates
• 320 degree viewing area for unsurpassed resolution
• Fits virtually every water/methanol kit on the market today!
• 0-5v analog output included for use with data loggers and virtually any engine management system

Special Order Item Only.

Seafoam Motor Treatment is a popular engine cleaner for rotary engines and can help free stuck seals within the engine that may have been caused by carbon build up.

This carbon can build up in many areas including

• On the rotors causing potential hot spots
• Over the apex seals contributing to reduced travel, hampering the seals ability to seal the combustion chambers from one another
• In Seal grooves reducing apex seals, side seals and corner seals ability to do their job as designed
• In Exhaust ports (especially on RENESIS RX-8 side exhaust ports)
• Sticking intake valves

Seafoam Motor treatment can help combat this harmful carbon and keep your engine in top condition.

Seafoam is oxygen (LAMBDA) sensor safe and can be used in a variety of ways, including adding the the fuel tank, or the most popular way on the rotary engine is to introduce a small amount undiluted in to the engine through the intake vacuum nipples found on the intake manifold of the rotary engine. The leaved it to soak and work its magic.

Please note that this procedure can result in engine damage if done incorrectly so Essex Rotary recommend consulting a professional with experience of this procedure prior to trying it for yourself.

Sold in a 16 fl ox bottle this is enough to do several treatments if used in the way described above.

Essex Rotary accept no responsibility for engine damage caused by using this product incorrectly.

This fan can be used as an upgrade to the OEM fan for more efficient cooling or fitment issues with aftermarket products. With its slim design, the fan can easily be installed flush against a radiator. For universal installation, use Mishimoto universal fan mount kit.

• High-flow fan provides 1850 cfm of airflow
• Universal fitment
• Compact design with a diameter of 406 mm and an overall thickness of only 73 mm provides increased engine bay space
• Easily reversible for use as a pusher or puller fan
• Mishimoto Lifetime Warranty

Specs

• Housing Diamiter – 16.75″
• Fan Diamiter – 385mm
• Blade Diameter – 15.375″
• CFM Rating – 1850cfm
• Fan Speed – 1800rpm
• Current – 34.0A (inrush)
• Current – 7.18A (normal)
• Voltage – 12volts

This fan can be used as an upgrade to the OEM fan for more efficient cooling or fitment issues with aftermarket products. With its slim design, the fan can easily be installed flush against a radiator. For universal installation, use Mishimoto universal fan mount kit.

• High-flow fan provides 1300 cfm of airflow
• Universal fitment
• Compact design with a diameter of 328 mm and an overall thickness of only 63.5 mm provides increased engine bay space
• Easily reversible for use as a pusher or puller fan
• Mishimoto Lifetime Warranty

Specs

• Housing Diamiter – 14.75″
• Fan Diamiter – 328mm
• Blade Diamiter – 12.875″
• CFM Rating – 1300cfm
• Fan Speed – 2200rpm
• Current – 15.1A (inrush)
• Current – 7.8A (normal)
• Voltage – 12volts

This fan can be used as an upgrade to the OEM fan for more efficient cooling or fitment issues with aftermarket products. With its slim design, the fan can easily be installed flush against a radiator. For universal installation, use Mishimoto universal fan mount kit.

• High-flow fan provides 1150 cfm of airflow
• Universal fitment
• Compact design with a diameter of 305 mm and an overall thickness of only 63.5 mm provides increased engine bay space
• Easily reversible for use as a pusher or puller fan
• Mishimoto Lifetime Warranty

Specs

• Housing Diamiter – 12.5″
• Fan Diamiter – 285mm
• Blade Diamiter – 11″
• CFM Rating – 1150cfm
• Fan Speed – 2000rpm
• Current – 12.7A (inrush)
• Current – 7.6A (normal)
• Voltage – 12volts

This fan can be used as an upgrade to the OEM fan for more efficient cooling or fitment issues with aftermarket products. With its slim design, the fan can easily be installed flush against a radiator. For universal installation, use Mishimoto universal fan mount kit.

• High-flow fan provides 950 cfm of airflow
• Universal fitment
• Compact design with a diameter of 255 mm and an overall thickness of only 60 mm provides increased engine bay space
• Easily reversible for use as a pusher or puller fan
• Mishimoto Lifetime Warranty

Specs

• Housing Diamiter – 11.5″
• Blade Diamiter – 255mm
• CFM Rating – 950cfm
• Fan Speed – 2300rpm
• Current – 13.08A (inrush)
• Current – 6.8A (normal)
• Voltage – 12volts

An ideal option if your looking to replace your Viscous cans found on older cars or installing oil cooler fans for some reason.
This Mishimoto fan controller is much more affordable than other kits on the market.

Take full control of your electric cooling fan with the Mishimoto Adjustable Fan Controller Kit! This kit is applicable for any 12v electric fan and includes all necessary components for installation. This kit can be purchased with a probe-style temperature sensor or with a 1/8″ NPT thread-in sensor to fit the needs of any project. The Mishimoto Fan Controller features adjustable activation from 66°C to 116°C and deactivates once temperatures are reduced by 6°C. This controller includes a built-in A/C override feature and is designed for use with 1–2 electric fans drawing a combined 25 amps or less. The Mishimoto Adjustable Fan Controller Kit includes the Mishimoto Lifetime Warranty.

Adjustment is simple via means of a slot head screwdriver to adjust the dial on the control box.

• Applicable for any vehicle with a 12v electric fan
• Adjustable activation temperature from 66°C to 116°C
• Includes probe or 1/8″ NPT style temperature sensor to fit your needs
• Includes 7 ft of wire for installation in nearly any size vehicle
• Built-in A/C override feature
• Designed for use with 1–2 electric fans drawing a combined 25 amps or less
• Includes wiring connectors and hardware for installation
• Mishimoto Lifetime Warranty

Essex Rotary would recommend the selection of the the 1/8th npt sensor over the probe style. The sensor can be installed in to a hose adapter like the Mishimoto hose adaptor.

PLEASE SELECT YOUR CORRECT MODEL APPLICATION FROM THE DROP DOWN MENU NET TO THE “ADD TO CART” BUTTON

From the selection on the drop down box below we offer the popular Racing Beat-modified High Performance Holley Intake System Kit for the 1974-1985 12A & 13B with stock port, street port and bridge port engines.

One of most significant benefits of this complete ready-to-go kit is that is takes all the guesswork, trial-and-error, and frustration out of attempting to assembly your own intake kit! We’ve taken over 40 years of our rotary engine experience and know-how and combined it for you in this complete, ready-to-install kit. Our intake kits has been thoroughly developed and tested using our in-house engine dyno to ensure maximum performance for each specific engine application.

The heart of each intake system is a performance-proven Holley carburetor. Depending on the requirements of each specific application, the carburetor is disassembled by Racing Beat’s carburetor technicians then reworked, retuned, and reconfigured specifically for use with a designated rotary engine application. This process is not a simple “re-jetting” project, but a complex series of steps requiring machining, drilling and reconfiguring of the main and metering bodies, adjustment of the float bowls, and complete replacement of all jets.

Headers must be used with these street port intake systems to achieve maximum horsepower gains.

The carburetors and manifolds used in these Holley kits are also available separately in the “Holley Components” section. Also see the “Intake” section for other related intake components.

Note: Installation of this kit requires use of a high performance fuel pump delivering 6 psi @ 20 gph.

PLEASE SELECT YOUR CORRECT MODEL APPLICATION FROM THE DROP DOWN MENU NET TO THE “ADD TO CART” BUTTON

Please Note that this item is special order only, and is subject to our non return policy for special order items under our T&C’s of sale. for more information please check out T&C’s here

Hypercarbon 800 Brake Pads from Project Mu In the correct shape to fit Various BBK’s (Please select your Kit from the drop down menu prior to adding your item to the shopping cart.)

When you need extreme stopping power with extreme performance applications, you need Project Mu HC800 pads. The HC800 is capable of 800 Celsius yet is still able to use effectively with little warming up.

HC800 is a genuine ‘cross over’ pad suitable for both track day and race conditions. The HC800 is extremely capable in competition environments, so use this pad if you are involved in serious track days, rallying, autocross, sprint, time trails etc.

Along with temperature capabilities, HC800 is renowned as a ‘driver’s pad’ with unmatched driver feel and control. Available in many shapes and thicknesses.

Please make your front or rear pad selection from the drop down menu above (next to the price)

(Please select your Kit from the drop down menu prior to adding your item to the shopping cart.)
Image is for illustration purposes only.

HKS Super Oil series were developed on the concept of “engine oil is one of the engine part”.HKS’ original “HIPER ESTER” can follow extreme boundary lubrication to any kind of engines on the metal absorbed molecular level. Each engine oil viscosity was determined specifically for the target engine for optimum engine performance. Super Oil is 100% specially blended synthetic oil.

HKS say 13BT oil is the best to use for the rotary turbo engine.
100% synthetic oil can prevent carbon from adhering to inside the housing that usually occurs in a rotary engine. HIPER ESTER maintains the oil film retainment under high temperature and airtightness inside the housing without risk to the rotary engine apex seals.

Sold as 20 Liter Drum

HKS Super Oil series were developed on the concept of “engine oil is one of the engine part”.HKS’ original “HIPER ESTER” can follow extreme boundary lubrication to any kind of engines on the metal absorbed molecular level. Each engine oil viscosity was determined specifically for the target engine for optimum engine performance. Super Oil is 100% specially blended synthetic oil.

HKS say 13BT oil is the best to use for the rotary turbo engine.
100% synthetic oil can prevent carbon from adhering to inside the housing that usually occurs in a rotary engine. HIPER ESTER maintains the oil film retainment under high temperature and airtightness inside the housing without risk to the rotary engine apex seals.

Sold as 4 Liter Can

HKS Super Oil series were developed on the concept of “engine oil is one of the engine part”.HKS’ original “HIPER ESTER” can follow extreme boundary lubrication to any kind of engines on the metal absorbed molecular level. Each engine oil viscosity was determined specifically for the target engine for optimum engine performance. Super Oil is 100% specially blended synthetic oil.

HKS say 13BT oil is the best to use for the rotary turbo engine.
100% synthetic oil can prevent carbon from adhering to inside the housing that usually occurs in a rotary engine. HIPER ESTER maintains the oil film retainment under high temperature and airtightness inside the housing without risk to the rotary engine apex seals.

Sold as 1 Liter Can

PIAA’s Extreme White Plus are possibly the brightest bulbs on the market, The HB4 fits the headlight units on the RX-7 FD and FC. putting out an equivilent of 115watts of light

These bulbs will provide a brilliant Xtreme cool white light that will light up road hazards and street signs long before a normal halogen bulb.

Xtreme White Plus bulbs achieve something few other high-performance bulbs can – and that’s deliver a stunning performance whilst complying with European regulations. Surprisingly only drawing 65/55 watts power, the bulbs convert the output of light to an equivalent of 110/100 watts, appearing far brighter than standard Halogen or Xenon units by emitting a crisp, blue-white, far-reaching beam.

Sold as a pair

Exclusive Size Available to Essex Rotary, These are not normally available for the RX-7 FC3s and are available in various sizes.

With the right Eibach Pro-Spacers installed, your car takes on a more aggressive look, with the wheels and tires—filling the wheel arches exactly the way they should.

Fine-tuning your track width doesn’t just enhance your car’s looks it also gives you improved handling performance and optimized roll characteristics. The 20mm Pro-Spacers will let you position your tyres exactly where they will look and perform their best. In many cases, installing the right Pro-Spacers can improve the look and function of your existing wheels and tyres so much, you might not need to buy new custom wheels and tyres at all.

Price quoted is for a pair of Eibach Hubcentric Pro-Spacers.

Please Select your desired size and delivery option in the drop down menu beside the price above.

Please note that these spacers only come in a 5 stud pattern

Original equipment replacement. Designed to improve original ignition system performance on vehicles using either electronic engine management systems . Conductor provides excellent RFI and EMI suppression to permanently eliminate the typical performance and fuel-wasting spark energy deterioration of OE and aftermarket carbon conductor wires.

All Magnecor leads are covered by a 10 year guarantee which ensures long lasting reliability and service life.

Please note these will only fit the Turbo II version of the RX-7 FC3s you will require a different set of leads if you have an FC3s EGI (NA version) running the old style distributor

Due to the ace of the FC these days this HT lead kit is made to order and usually takes around 7-10 days for arrival at our shop ready to be shipped on to the customer.

Magnecore Number 45284

Essex Rotary bring you another high quality part from the legendary gods of rotary RE-Amemiya
The Response Cleaner Intake kit is a high quality filter designed to fit in to your FC3s Turbo II produced from 1989-1991

RE-Amemiya boasts a increase in response at higher revs in the FC3S due to their Dual-Entry Air filter intake design. The RE-Amemiya Response Cleaner Air Filter System will be a complete bolt-on kit and is an easy and clean way to increase both response and power for your FC3S.

Special Order only so please allow 2-6 weeks for delivery.

This is Pineapple Racing’s exclusive Heavy Duty Water Seal kit. Pineapple Racing tested these seals for over 7 years in numerous street and track cars before offering them to our customers. They have proven to be a significant upgrade over the stock water seals. Pineapple Racing use them in all their 5-year warranty motors.
Also, these seals are re-usable if you need to reopen the motor to freshen it, as long as the mileage is not too high or the engine too overheated. In other words, if you make a mistake and blow up your engine or perhaps improperly clearance the seals or whatever, these seals can be removed, allowed to “rest” for about 30 minutes and be reused when you put the engine back together. Stock water seals must be disposed of when freshening an engine, even with just a couple heat cycles.

Kit includes

• Water jacket o-rings
• Front cover o-ring (and backup washer, if needed application dependent)
• Dowel o-rings
• Rear stationary gear o-ring
• Oil pedestal o-rings or Gasket (depending on application).
• Oil Metering Pump “O” Ring
• Dowty Washer Set (Tension Bolt Washers)

Please note this kit is for a Series 5 RX-7 FC Engine,
Please allow around 28 days for delivery if not in stock.

Pineapple Racing Solid Dowel Pins

• Helps prevent cracking the plates from hp loads or “ping” (esp. important in the 20B and Series 5 & earlier turbo engines)
• Spreads the load across the length of the engine.
• Helps to insure a true engine centerline which reduces engine failure and increasing bearing life
• Using an external oil line provides a more even oil pressure to the main bearings
• Low cost, easy installation
• Available for: 12A, 13B and 20B (12a and 20b Special Order)
• Custom lengths available (Special Order)

Pineapple Racing Solid Dowel Pins provide an easy, cost effective aid to hp and “ping” loads causing plate cracking or engine damage from loss of clearance from engine flex. Our super strong proprietary material has been meticulously machined to provide what we feel are the most accurate and consistently machined solid dowel pins on the market. The O.D. is accurate to 50 millionth’s! That’s 0.00005”. We “lightly” tapped one end for use with a Dowel Pin Puller.

Replace just the lower dowel pins helps to insure your engine’s centerline remains true. It is a great update requiring no machining.

Replace both lower and upper dowel pins for the maximum improvement. Replacing the upper dowel pins requires the installation of an external oil feed line to the front main oil galley to replace the OEM galley in the OEM dowel pins. Our Oil Pedestal Adapter kit makes this a simple job that can be done with simple hand tools and an electric drill.

High horsepower and the shock loads from “ping” put a tremendous load against the rotor housings. The load deflects the rotor housings outwards, pushing the dowel pin with them. The dowel pins are retained by their fit into the cast iron plates. If the loads are too high, the upper dowel pin can cause the plate(s) to crack. Additionally, since the upper dowel pins are also used as an oil galley, a massive oil leak is also possible. The OEM 20B is especially prone to this type of damage,  and with the price of the “thick” center plate near $1800us, preventing this type of damage pays for itself.

The Pineapple Racing Oil Pedestal Adapter is a stylish, Nickel plated rotor shaped adapter. It easily installs between the existing oil filter pedestal and the rear plate. It features a ¼”NPT port for an external oil line and an 1/8” NPT port for oil pressure or oil temperature.

Please allow up to 28 days for delivery if not in stock.

Venturi Drive Super Sound Blow Off Valve – Release Type

The all new ribbed main body dissipates heat more effectively and the venturi shaped funnel creates a sharp dynamic sound.
Venturi Drive dump valves also feature “Dual Drive” for maximum response, a small port for low boost and a larger port for high boost.

The main purpose of the dump valves is to improve the response of the turbo by quickly releasing the boost pressure before the turbo stalls.

They are made from die cast polished aluminium with a brass piston and a rubber diaphragm, meaning they can easily cope with boost pressures up to 1.2 bar with the supplied spring.
There is an alternative hard spring for boost pressures above 1.2bar and also a soft spring available for very low boost applications.

Blitz VDSS Blow Off Valves  are also tension adjustable.

This kit includes everything needed to install onto your vehicle. (Please remember that most of these kits are designed to install on a standard setups so if you intend to install this on a single turbo conversion some modification may be required)

This kit is a Release Type

Please allow up to 28 days for delivery for this item if not in stock.

Refresh your FC’s tired suspension with Bilstein’s B6 Sport dampers.

Performance you can feel.

If you expect more damping power from your shock absorber even under loads but dont want to opt for an all out sports model.

The Bilstein B6 is the ideal solution.

The product benefits at a glance:

• Increased power reserves and service life – even when pulling transporters and trailers or during frequent journeys with loads
• Optimum adhesion and enhanced lane change stability in both day to day and extreme situations
• Marked improvement in safety and sportiness without additional spring changes (lowering)
• Bilstein gas pressure technology
• Bilstein mono – tube/Upside – Down technology – made in Germany
• Road – tested by Bilstein and fine – tuned
• No German TuV registration required

Sold Individually
Please select front or rear from the drop down menu

Save Oner 10% when buying a complete set for your FC plus savings on combined delivery.

Image is for illustration purposes only and may not represent the actual damper design you will receive.
Please allow up to 28 days for delivery.

Designed originally for racing engines, today’s compact production engines can also benefit from the use of GReddy’s Radiator Breather Tank. This tank efficiently removes trapped hot air pockets within the cooling system which can eventually cause over heating, especially during spirited driving. Allows the radiator to perform more effectively, improving overall cooling performance. Requires radiator hose adapter for installation (sold separately).

This Item is a Universal fit so may require some custom pipe work to work correctly on some vehicles.

Please allow up to 28 days for delivery is not in stock.

Expand your GReddy Profec OLED Boost Controller to do so much more.
The GReddy Profec MAP connects to the current GReddy Profec OLED Boost Controller and, through boost maps, provides even finer control over your vehicle’s boost pressure. Boost correction is not the only added function in the addition of the Profec MAP! The following features have been added:All parameter settings can be set by PC via USB cable (sold separately), Display Gear Position, Speed, RPM, Engine Temp, Throttle Position, Backlight dimming and scramble boost switching functions.

Overview
Expand your boost control with additional features using the new Greddy Profec MAP! For use with Greddy Profec (P/N 15500214) This new MAP easily plugs in between the Profect Display/Control unit and Profec main unit, with some additional connections depending on application.

Features

• Boost Map Correction – Fine boost tuning settings via 10×10 boost maps (Load vs Duty %)
• Boost Correction by RPM, Throttle Position, Speed, Gear Position, or Water Temp Example: Boost can be lowered if the car is not within the desired operating temperature. Using the Gear Position feature, boost can bet adjusted individually for each gear and engine speed.
• Addtional Profec monitoring and data loging via PC software.
• AUX input for Over Take Boost Function future using optional Remote Swithcing System
• PC Compatiable (Profec MAP software) with use of mini-USB to USB cable (sold seperately)

Notes

• Plugs-in easily inbetween Profec Display/Control unit and Profec main unit (Additional connections depending on application.)
• PC Compatiable (Profec MAP software) with use of mini-USB to USB cable (sold seperately)
  • OS: (Japanese, English) Windows Vista, Windows 7 (32bit, 64bit)
  • CPU: 1GHz or more 32bit or 64bit processor
  • Memory: 1GB or more
  • HDD free space: 20MB or more

  Please allow up to 28 days for delivery if not in tock,

HKS Super SQV (Sequential Blow Off Valve) uses a unique sequential valve structure and a differential pressure control system, which allows for a broad operating range from low boost to high boost. Its Pull-Type relief design ensures stable operation regardless of the amount of boost pressure. The Super SQV will support new generations of turbocharged vehicles.

Universal Kit includes

• SQV Blow Off Valve
• O-ring,
• C-ring (Securing Clip)
•  Vacuum Hose T-fitting 6×4×6
• Vacuum Hose T-fitting 4×4×4
• Inline Air Filter and Tylap.
  

HKS Part Number: 71008-AK001

Please Allow up to 28 days for delivery for delivery.

HKS Silent Hi-Power mufflers offer high performance and sporty appearance with the added benefit of reduced noise levels making it the best choice for more mature enthusiasts. Silent Hi-Power mufflers are constructed entirely of SUS304 grade stainless steel for high lustre, long lasting performance. For certain applications, HKS has introduced the “Silent Chamber” which removes a lot of the lower frequency noise that can often be heard into the cabin even when cruising. The silent chamber removes this uncomfortable noise but due to its closed end design, only a minimal amount of exhaust gas flows into it, meaning that the disruption to exhaust gas flow through the entire system is minimized and there is no harm to performance.

Image is for illustration purposes only.

Totally reliable brake fluid that combines a boiling point so high it’s in another dimension with durability and maintainability. You know it’s time to change your G-four 335 brake fluid, which can reach close to 300C, when the color changes from green to crystal clear.

Project Mu’s G-Four 335 Brake Fluid had one of the highest boiling points in the industry at 335℃, giving you confidence on the brakes no matter how hard you lean on them.

Brake fluid is often overlooked as a performance upgrade when looking at brakes, When upgrading your brake system, you should always improve the quality of your fluid to match the increased demands on your braking system.

Specs:

• Type : Glycol/100% Synthetic
• Dry Boiling Point : 335℃
• Wet Boiling Point : 221℃
• Volume Per Bottle : 1000ml

DO NOT MIX WITH OTHER OILS

Normally in stock however please check prior to ordering if you need this brake fluid urgently.

This Alternator has been specially selected by us as an ideal replacement for your original alternator if it has failed.

With a 100A output and and OEM quality fitment your all set to power up your FC Turbo II once again.

This item can take up to 28 days for delivery once ordered. though typical delivery times are much quicker.

High Quality Replacement Clutch Slave Cylinder for the Mazda RX-7 FC3s This will fit the 2nd Generation RX-7 EGI Only
Many owners are choosing to replace their clutch Master and Slave Cylinder as a precautionary measure, There is nothing worse then a brake down due to a leak on either of these cylinders.

Common signs of slave cylinder failure include

• The Pedal failing to return to the top when released
• Clutch fluid leaking from the Cylinder
• Inability to select gears

High Quality Replacement Clutch Master Cylinder for the Mazda RX-7 FC3s This will fit all 2nd Generation RX-7′s
Many owners are choosing to replace their clutch Master and Slave Cylinder as a precautionary measure, There is nothing worse then a brake down due to a leak on either of these cylinders.

NOT ALL 13B ENGINES RUN 3MM APEX SEALS, PLEASE CHECK YOUR APPLICATION BEFORE ORDERING.

Thanks to our close association with the new UK distributor of Goopy Performance products Essex Rotary can now offer this superb proven more durable alternative to the standard Mazda Apex Seals.

Goopy Apex seals have become renowned for their reliability by withstanding up to 50psi in Drag Racing and still not failing and have even withstood detonation that the Mazda Apex seal could only dream of.

This makes these High Performance Apex seals not only ideal for any N/A, Turbo or Supercharged 13b but also ANY standard or tuned 13b engine running 3mm seals .

Goopy Performance recommend .0015″ of clearance between the apex seal and the rotor slot for all applications, boosted or naturally aspirated.

3 mm 13B Goopy Apex Seals are .115″ (2.921mm) thick, and you should be able to slide a .0015″ feeler gauge into the rotor apex slot with a new apex seal.

Goopy oversized 3 mm seals measure .118″ + / – .001″  (2.997mm  +/- 0.025mm). If your rotor slot measures .018″ – .020″, you may benefit from our oversized 2 mm seals which will allow you to re-gain the .0015″ suggested clearance.

Also available for the RX-8 engines these seals can be included in your Essex Rotary engine rebuild upon request at a small additional cost.

Sold at a set of 6 complete seals these will easily replace the stock apex seals found in some factory 13b engines or builds with 3mm machines slots.

Due to their increased popularity please allow up to 21 days for delivery

Genuine Mazda Factory Race Part

Use in place of stock rear bearing. 3-window type. Recommended for any engine used at 8000 rpm and above. Increases oil flow to the inside of eccentric shaft and to rotors.

If you are installing this bearing in to a Manual RX-7 FD3s of 231ps RX-8 Rear Stationary Gear we would recommend getting an indexing groove cut in to the rear face of the stationary gear in order to locate and hold this bearing correctly. The location should be in the same place as that found on Auto Rear Stationary gears and those earlier then the FD3s. Stationary gears from the Automatic FD3s and RX-8 including the 192ps manual RX-8 should have this indexing groove in them already.

These bearings are special order only and can take up to 6 weeks for delivery. They are sometimes out of stock at Mazda HQ Japan so can take longer. we would recommend ordering your competition bearings early to avoid disappointment.

THESE BEARINGS ARE SOLD INDIVIDUALLY

The Mazda Factory Race (MFR) rotor bearings for all 12A & 13B engines are the best bearings available of engine operation near or above 8500 RPM. The rotor bearings are manufactured with a deep groove for additional oil storage and offer an additional .0005″ (approximate) clearance. These bearings can be used in 1973 and earlier engines by grinding off the indexing tab.

Competition bearings have 0.01 inch deeper oil groove and provide 0.0005 inch more clearance than stock bearings. Thinner overlay material improves bearing service life.

These bearings are special order only and can take up to 6 weeks for delivery. They are sometimes out of stock at Mazda HQ Japan so can take longer. we would recommend ordering your competition bearings early to avoid disappointment.

THESE BEARINGS ARE SOLD INDIVIDUALLY

Mazda 12A/13B Engine Twin V-belt Alternator Pulley

GFB lightweight pulley kits are made from aircraft-grade 6061-T6 aluminium and offer faster acceleration through significant weight reduction on the crankshaft. The effect is similar to a lighter flywheel, and the car feels more lively and willing to rev.

Most of our kits are underdriven, which means the accessories are driven slightly slower to reduce parasitic losses. It should be noted that our underdrive pulley kits do NOT adversely affect the operation of the accessories. If they did, we would not sell them!

Lightweight Alloy Pulley

• Improved throttle response and acceleration through significant reduction of rotating mass
• Engine feels more free-revving
• Under-driven kits offer more power through reduction of parasitic losses from the accessories with NO adverse affects on their operation
• Suitable for Sa22c, FB3s and FC3s Engine setups.

Compatible with both 12a and 13b Engine that run the old style V Drive Belts.

Go Fast Bits Product Code: 2215

Please allow up to 28 days for delivery of this pulley if not in stock.

This 4 Point version of Ultra Racing’s FC3s Rear Strut Brace offers you superior chassis rigidity compared to their 2 point version.

Ultra Racing Strut Bars are mounted on top of the suspension top mount and fit all vehicles without any modifications. Made from hollow steel the Ultra Racing Strut Bar are a one piece design which makes them more rigid than the bolted alternatives. This means that when cornering or under heavy braking the Ultra Racing Strut Bar keeps the front stable which improves handling. For maximum handling improvements fit the Ultra Racing Strut Bars with uprated suspension components including coilovers or lowering springs.

Advantages of Upgrading Your Strut Bars;

• Adds more stability
• Fits without modifications
• Solid one piece design
• Works with upgraded suspension

Ultra Racing Strut Bars are mounted on top of the suspension top mount and fit all vehicles without any modifications. Made from hollow steel the Ultra Racing Strut Bar are a one piece design which makes them more rigid than the bolted alternatives. This means that when cornering or under heavy braking the Ultra Racing Strut Bar keeps the front stable which improves handling. For maximum handling improvements fit the Ultra Racing Strut Bars with uprated suspension components including coilovers or lowering springs.

Advantages of Upgrading Your Strut Bars;

• Adds more stability
• Fits without modifications
• Solid one piece design
• Works with upgraded suspension

The Ultra Racing lower bars come in different sizes and fitment as they are developed to improve different characteristics of a cars handling. Not only do the Ultra Racing lower bars improve the cars stability under heavy load, the side lower bars will also reduce the damage from a side impact collision.

This kit is a 4 point brace setup, the kit comes with a pair of braces one for each side of your FC3s

The Ultra Racing Anti Roll Bars (Sway Bars as they are also known) are thicker than the standard OE Anti Roll Bars and are manufactured in steel. This stiffens the lower suspension components which helps to eliminate excess oversteer and understeer.

The body roll of the car will also descrease because the thicker Ultra Racing Anti Roll Bars help keep the car flat when cornering which provides better cornering especially at high speeds.

Advantages of Upgrading your ARB’s;

• Stiffens lower suspension components
• Eliminates excess understeer & oversteer
• Reduced body roll
• Complete with uprated bushes

Specification: 19mm Solid (Standard 16mm Solid)

Ultra Racing offer this cross chassis brace bar, mounted to either side of the inner chassis/door sills the aim is to help stiffen your RX-7 FC3s

Simple bolt in design makes installation simply.

The Ultra Racing lower bars come in different sizes and fitment as they are developed to improve different characteristics of a cars handling. Not only do the Ultra Racing lower bars improve the cars stability under heavy load, the side lower bars will also reduce the damage from a side impact collision.

Ultra Racing Strut Bars are mounted on top of the suspension top mount and fit all vehicles without any modifications. Made from hollow steel the Ultra Racing Strut Bar are a one piece design which makes them more rigid than the bolted alternatives. This means that when cornering or under heavy braking the Ultra Racing Strut Bar keeps the front stable which improves handling. For maximum handling improvements fit the Ultra Racing Strut Bars with uprated suspension components including coilovers or lowering springs.

Features Include;

• Adds more stability
• Fits without modifications
• Solid one piece design
• Works with upgraded suspension

These inner wing (fender) braces from Ultra racing are designed to stiffen up your front end, utilising their 3 point mount design  the chassis ares that supports the front suspension towers can be made more rigid, resulting in reduced chassis flex.

Features Include.

• Extra front chassis support
• Improves braking and stopping performance
• Reduces noise,vibration and hardness
• Improves high speed cornering

Please allow up to 28 days for delivery of your item if not in stock, in extreme cases this may be longer, if delivery time is an issue please contact us in advance prior to placing your order.

Power FC Commander (handheld unit) compatible with the A’pexi Power FC.

The FC COMMANDER is a hand held controller designed to allow access to the vital parameters within the Power FC. The unit allows a wide range of data modification through its large back lit LCD display. The unit has been designed so that one finger can control a wide array of data. Once connected, the Apex logo will appear in the screen taking the user to the Main Menu. From here, the user can access the three Main Menus (Monitor, Setting, Etc.) The FC COMMANDER “communicates” with the Power FC control unit thereby creating one of the first interactive user friendly fuel management systems.

The Power-FC is Apex’s solution to all of your tuning needs and stands as the flagship tuning device in the APEXi lineup of electronics. Depending on your needs you can order anything from replacement sensors and harnesses, or components such as the FC Commander, FC Commander Software, and Boost Control Kit to further complement your Power FC needs.

The Apex Down Pipe is the pipe on turbo vehicles that connects the turbine exhaust housing to the catalytic converter. Although short in length, the Apex downpipes provide incredible amounts of power because the piping diameter is enlarged so early on the exhaust system. This enlargement in diameter results in a dramatic increase in exhaust flow capacity as well as a significant reduction of back pressure. The GT spec Down Pipes are constructed of fully polished SUS 304 stainless steel. The N1 Down Pipes come with our trademark black powder coated mild steel pipes.

The N1 Dual is a hybrid variation of the N1 exhaust. This system incorporates a twin pipe, twin canister design for improved mid-range torque without sacrificing top end power. The twin piping is constructed of mild steel with a titanium particle coating mated to SUS 304 polished stainless steel canisters. Each canister features a polished 90mm (3.54 inch) tip. Robotic TIG welds compliment the hand crafted MIG welds to create on of the most innovative and dynamic exhaust systems on the market.

The Power Intake is the premier air filter designed to create pure horsepower. The intake funnels used in racing machines take advantage of a characteristic where air travels along the side of the side of surfaces. However, the center portion of the funnel is virtually unused. It is this concept that gave birth to the Dual Funnel design. A primary funnel on the top portion of the air cleaner was inserted to channel the air flow directly into the lower funnels at the base of the cleaner. This design was a huge success on the former Super Intake model. The Power Intake took this design and improved the flow characteristics. New funnel design, element material and air flow channeling characteristics make the Power Intake one of the most efficient air cleaners on the market today. By constructing the upper and lower funnel from a highly durable injected resin, engineers were able to construct the ideal shaped funnel previously not possible with the stainless steel material. Funnel shapes focused on increasing air speed without changing the flow direction of the intake air. The result is a high speed and smooth flow of air into the intake. The lower funnel has been engineered at a 14 degree curve for maximum efficiency. Also, the lower funnel position has been made even closer to the base of the cleaner to reduce drag and eliminate any _dead spotsb within the cleaner.

The Power Intake incorporates a newly developed material (layer filter of dry density fibers) which improves the element density. This allows maximum protection from foreign materials entering the engine. Compared with past model, the Power Intake has also succeeded in decreasing its ventilation resistance by about 10% (pressure loss) for maximum performance and protection. The Power Intake is dry-type filter and is trouble free. Some of the problems associated with wet type cleaners, such as oil sticking to the air flow meter, are a thing of the past. The Power Intake is basically maintenance free. Filter replacement, when necessary, can be done at a very low cost.

CONCEPT:

• Air filter with minimal air-flow restriction

CHARACTERISTICS:

• Dual funnel filter system minimizes intake turbulence

Hypercarbon 800 Brake Pads from Project Mu

When you need extreme stopping power with extreme performance applications, you need Project Mu HC800 pads. The HC800 is capable of 800 Celsius yet is still able to use effectively with little warming up.

HC800 is a genuine ‘cross over’ pad suitable for both track day and race conditions. The HC800 is extremely capable in competition environments, so use this pad if you are involved in serious track days, rallying, autocross, sprint, time trails etc.

Along with temperature capabilities, HC800 is renowned as a ‘driver’s pad’ with unmatched driver feel and control. Available in many shapes and thicknesses.

Please make your front or rear pad selection from the drop down menu above (next to the price)

Image is for illustration purposes only.

NS400 Brake Pads from Project Mu

The NS400 Brake Pad range by Project Mu is developed as their competitively priced performance compound for most popular automotive applications.

A must for any vehicle that has increased horsepower and stage 1 modifications, this motorsport derived sports pad provides a considerable braking performance increase over standard factory equipped brake pads, but is keenly priced to suit all budgets.

The NS400 provides outstanding initial stopping power, and is asbestos-free. The NS400 also exhibits excellent low dust and squeal properties.

Please make your front or rear pad selection from the drop down menu above (next to the price)

Image is for illustration purposes only.

Tie rod ends are designed with high quality alloy steel. These tie rod ends are designed to have maximum accuracy, which enables them to sustain extensive load.

Features.

• Correct tie rod geometry on lowered cars by keeping them horizontally straight
• Reducing under steer and bump steer
• Increasing in steering stability
• More controllable car during hard driving
• Reversed design for optimum steering angle on lowered vehicles
• Direct bolt-on with OEM components

Please Allow Up to 3 weeks for Delivery.

Increase your steering angle and upgrade the strength of your steering components with thee Hard Tie Rods from Hardrace.

Features

• Manufactured from high-tensile, forged steel
• Suitable for track and road use
• 5mm built-in rack spacer to increase steering lock

Please allow up to 3 weeks for delivery of these items.

Save on a 6 bottle pack plus combined Shipping. Save £27.94 on this pack, This pack works out at £15.00 per bottle
A Full Synthetic Oil SAFE for your Rotary Engine
This should be enough oil for your to carry out an oil change and have spare to top up with.

Do you feel that you aren’t getting the power you should be from your rotary engine? Are you experiencing bearing wear under severe (or possibly under not-so-severe) operating conditions? If so, you may be using the wrong engine oil. Idemitsu 10W-30 can reduce or even eliminate some of the problems you may be having.

As the developer of the engine oil for the winning 1991 LeMans Mazda 787B and a long time supplier of vital lubricants to Mazda, Idemitsu has intimate knowledge of the requirements of rotary engines.

• With the precise base oil mix of PolyAlphaOlephins and PolyEsters, Idemitsu Rotary Engine Oils are able to minimize those deposits on your apex seals. 
• Allows for better sealing of the chamber, facilitating more power generation. 
• Extends the life of turbochargers by reducing bearing coking.
• Specially developed additives facilitate even tooth load on the front stationary gear to allow for higher loads and higher RPM.
• Premium anti-wear agents create a strong film between the main bearings and the eccentric shaft, reducing metal-to-metal contact and minimizing bearing wear.
• Developed to reduce entrained gas generation. Entrained gases reduce the oils ability to prevent metal-on-metal contact, thereby increasing main bearing wear.
• Includes Molybdenum as a friction modifier. This compound reacts with the metal surfaces to create a low-shear boundary. The low shear characteristic reduces friction, increasing efficiency and power output. 

A full synthetic oil specially formulated for your rotary engine from Idemitdu

Each Bottle contains 1 US Quart of Oil

Blanking plate kit for RX-7 FC3s Turbo II from the famous Japanese rotary tuner Super Now
This kit is used when removing Air Control Valve (ACV) to simplify the intake manifold and engine bay.
Made from 8mm aluminium with an anodized finish.
Not suitable for Turbo II engines still running the stock air pump system.

This Kit contains 4 blanking plates.
Please allow up to 3 weeks if these items are not in stock. if you require this part quickly please contact us before ordering.

This Awesome Assembly Lube is used on all our engine rebuilds here at Essex Rotary, It makes the assembly of tight fitting close tolerance parts a breeze while still offering excellent protection for parts like stationary gears on initial start up.

Here is what Royal Purple have to say.

Max-Tuff is an ultra-tough, synthetic lubricant. It’s designed for engine builds and repairs. Max-Tuff utilizes unique, synthetic molecules that adhere to metal surfaces to create a formidable, load-bearing physical barrier between surfaces. This minimize the metal-to-metal contact and wear in boundary lubrication conditions, and provides excellent protection against rust and corrosion of both ferrous and nonferrous metals.

PERFORMANCE ADVANTAGES

• Greater wear protection
• Clean, efficient equipment
• Extends equipment life
• Compatible with conventional mineral and synthetic oils
• Non-foaming
• Outstanding rust / corrosion protection
• High temperature service capability

Sold in an 8oz bottle

Genuine Mazda Rotor Bearings
These are the standard rotor bearings for 12a and Early 13b’s including the RX-7 FB/SA22c and FC3s

Please note these are the most common size however we are able to offer an oversized option for the Fc3s if required

These bearings are sold as a pair (2 bearings) so one for each rotor.

Please be aware that if these bearings are out of stock it may take up to 3 weeks to get your parts to you, if you require fast delivery then we recommend you contact us prior to placing your order so that we may check availability and pricing for express delivery.

Sold as a Pair these stationary gear bearings where used in many of the early Rotary engines

These include

• RX-7 FB/SA22c
• RX-7 FC EGI
• RX-7 FC Turbo II
• RX-8 192ps (4 Port Manual)
• Rx-8 Auto (4 Port Automatic)

These bearings have fewer “windows” but are the correct bearings for most 12a and early 13b engines (with the exception of the 13b REW found in the RX-7 FD3s)

If your looking at these for your 4 port RX-8 engine then a popular upgrade is the high power multi window bearings though there is no locator notch found on the high power bearings here at Essex Rotary we install them in conjunction with a high quality “bearing lock” compound to help keep them in place.

Sold as a pair of bearings.

if out of stock please allow up to 3 weeks for delivery, if your in need of these parts quickly then we recommend you give us a call prior to ordering.

A popular battery upgrade for your standard battery bringing unrivaled 720CCA starting power to your car. whilst shaving some weight from your car.

OPTIMA® REDTOP® 35 Ultra high-performance SPIRALCELL TECHNOLOGY® AGM (absorbent glass mat) battery with reliable cranking power for your auto, car or truck and twice the life. The OPTIMA® REDTOP® will outperform and outlast traditional batteries in demanding cranking/starting applications. The ultimate high-CCA starting battery for vehicles that have alternators capable of keeping up with all electrical loads.

BENEFITS OF THE REDTOP®:

• Strongest five-second starting burst
• Up to two times longer life
• More than 15 times the vibration resistance
• Completely spillproof, mountable in virtually any position
• Maintenance-free
• Faster recharging
• Optimal starting power

Dimensions: 239mm(L) x 172mm(W) x 190mm (H) inc terminals
Weight: 14.4Kg

Please note the optima 35R is a little shorter then the standard battery so a packer will be required raise the battery in its box for proper installation.  In times when the 35R may be out of stock we may substitute your order with the 3.7R (a near identical battery) to aid in getting your battery to you quickly.

12 volt drycell battery delivery a whopping 680 Pulse Cranking Amps

ODYSSEY Extreme Series Battery Model PC680
(internal threaded brass terminals, M6 SS bolts, and L bracket adapter)

Powersport vehicles need a powerful battery that’s built to take the constant pounding that comes with the territory, whether it’s is on land, sea, or snow.

The ODYSSEY battery can handle it. Featuring rugged construction and packed tightly with pure lead plates, the non-spillable AGM design ODYSSEY battery protects against the shock and vibration that can quickly destroy other batteries. And the pure lead plates mean more power-twice the overall power and three times the life of conventional batteries-up to 400 cycles at 80% depth of discharge!

Specification

• AGM Technology
• 170CCA
• 16Ah
• Reserve Capacity 24 Minutes
• Dimensions 181.5(L) x 76.3(W) x 167.8(H)
• Weight 7Kg
• Terminals M6 Threaded Terminals (fasteners included)

Please note that due to the nature of these small lightweight batteries they may not be suitable for vehicles with a large electrical drain that are left for extended periods without being used.

The PC680 will require a terminal kit if you with to use traditional battery terminals with it.

Part description:

RX-7 FC3S Ver. 1 with customizable progressive indicator
The brake and running LED tail lights look similar to genuine Mazda tail lights but have a subtle customized flare which you can see when you use your indicator lights.
We hope that you are satisfied with these innovative, ‘like new’ lights for your RX7.

Product details:

Included

Tail lights (left and right)

Each light is riveted with an official Car Shop Glow authenticity badge.

Build

Cleaned second-hand parts
Lens split and LED board fitted
Wires pressure bonded
Lens refitted
Smoke applied
Clear coat finish
All production is done in Japan.

Shipping:

These items are made to order and shipped directly from Japan via Air Mail.

Air Mail is a quick option for shipping your items. Air Mail orders usually takes from 2-6 weeks depending on stock availability.

Please note that the Air Mail shipping , which will be added to your order at checkout only covers Air Mail shipping of your item from Japan and importation fees. There will be an extra charge to ship your item from our warehouse to you once your item has arrived in the UK. Please contact us for a quote for UK shipping.

Warranty:

This product is guaranteed for 6 months against problems such as clouded lenses from water, condensation, electrical shortages, burnt out LEDs, and fogginess.
After a damage part is returned, we will repair or exchange the part. For details pertaining to returned parts please refer to our terms and conditions. (Return postage paid by the customer is required.)
We are not liable for any damage to the parts except for when the installation or repair is being completed on company premises.

Compatible Models:

RX7 FC3S

Mounting:

Genuine OEM couplers are used in mounting.

Water Methanol Injection at its finest!

Our Top system for your Turbo-/Supercharged car. 2D-Mapping thrugh fuel injection and/or boost. Easy programmable LCD-display incl. new Dual Stage Technology and terminated weather tight OEM harnessed wiring connections !
Award winning system – The controller creates a delivery map based boost and/or EFI signal. For all charged and naturally aspirated engines with traditional EFI system.

Boost Cooler Waterinjection

Obtain up to 10-25% more power in your turbo- or supercharged engine, even if it´s pre-tuned, by using the Boost Cooler™-Water/Methanol Injection System!

The main function of the Boost Cooler is to suppress detonation caused by high temperature and pressure developed within the combustion chamber when the effective compression ratio has been taken beyond the auto-ignition point by either a turbo or a supercharger.

Water, with its high latent heat content, is extremely effective for controlling not only the onset of detonation but also the production of oxides of nitrogen in the modern leanburn engines.Furthermore, the Boost Cooler doesn’t create an intake restriction like an intercooler, and unlike race gas, it reduces intake air temps up to 60°C and improves charge air density too!

Snow Performance systems effectively steam clean the valves, valve seats, and even the piston tops and intake when they inject. This reduces carbon build up. The Boost Cooler™ can be installed in a matter of hours without having to remove bumpers or do custom intake piping.

Boost / Fuel Injection controlled variable injection

Award Winning System! – The Stage 3 Boost Cooler® is unmatched for accuracy and adjustability in water-methanol injection systems! This system can be used on any forced induction engine, or ANY engine with a traditonal EFI system, and features our LCD display with on-the-fly adjustability.

Easy Installation

Extremely easy to set up and dial in – the software creates a delivery map based on boost and/or EFI signal from just a few easy to set points you punch in from the drivers seat. The LCD Screen displays boost pressure, fuel injector duty cycle, as well as water-methanol injection percent. Quick, easy, positive adjustments are made with 2 push buttons. Low profile design allows for easy-to-view and discrete mounting

Dual Stage Technology

The Stage 3 has the ability to progressively command  2 Hyper-Sonic™ Nozzles independently of one another. This sophisticated dual stage injection management yields the highest increases in HP and cooling along all stages of the engine allowing you to greatly increase the boost & timing of your vehicle safely. The DST-Upgrade is already included in the Stage 3 systems.

Boost Cooler Stage 3 EFI – Ideal for any traditional manifold injection engines (electronic fuel inj.) :

• AUDI Turbo (e.g. Audi A3 8L/8P, A4 B5/B6/B7, A6 C5, TT 8J/8N)
• Opel Astra H (z.T. auch J), Insignia, Vectra C, Zafira
• Porsche 911 Turbo (964, 993, 996), 924/944 Turbo
• VW Turbo (Bora 1J, Golf 4,  Jetta 3, Passat 3B)
• and many more.

Features:

• Boost controlled, variable injection
• Terminated weather tight OEM harnessed wiring connections
• Dual Stage Technology
• Efficient Intercooling, up to 60°C lower air intake temperature
• Achieve approx. 116-Octan rating, by using ordinary 95-Octan gasoline
• Reduces EGT and oil temperatures
• Allows you to run safely more boost and/or more timing
• Reduces thermical stress on NOS, LPG/Autogas and pre-tuned engines like chiptuning & higher boost levels
• No wear issues, only clean combustion chambers
• No loss of boost as with an intercooler
• Reduces the specific fuel consumption
• Easy installation

Water Methanol Injection at its finest!

The latest development from Snow Performance!

Complete kit with freely programmable 52mm OLED-gauge and optionally Dual Stage Technology.

Boost Cooler Water Injection

Obtain up to 10-25% more power in your turbo- or supercharged engine, even if it´s pre-tuned, by using the Boost Cooler™-Water/Methanol Injection System!

The main function of the Boost Cooler is to suppress detonation caused by high temperature and pressure developed within the combustion chamber when the effective compression ratio has been taken beyond the auto-ignition point by either a turbo or a supercharger.

Water, with its high latent heat content, is extremely effective for controlling not only the onset of detonation but also the production of oxides of nitrogen in the modern lean burn engines.Furthermore, the Boost Cooler doesn’t create an intake restriction like an intercooler, and unlike race gas, it reduces intake air temps up to 60°C and improves charge air density too!

Snow Performance systems effectively steam clean the valves, valve seats, and even the piston tops and intake when they inject. This reduces carbon build up. The Boost Cooler™ can be installed in a matter of hours without having to remove bumpers or do custom intake piping.

52mm OLED Control Unit

The all new Snow Performance Stage 2 Boost Cooler water-methanol injection system comes fully revamped for all boosted (turbo- and supercharged) vehicles and uses a progressive 52mm-gauge style controller that proportionally injects more or less according to boost pressure.
Start and full points are adjustable for engagement and delivery curve to match what the engine requires. Proportionally injecting according to boost pressure gives an accurate delivery of water-methanol and allows cooling and performance improvements over a wide range for improved drivability.

Displays :

• Boost pressure (S2E / EURO-Edition in BAR)
• Boost Cooler percentage of injection
• Low level of the fluid reservoir
• Secondary nozzle activation
  (Dual Stage Technology, optionally as upgrade)
• 2 specific fault modes
  (Clogged line, broken line)

Dual Stage Technology (DST)

The Stage 2 has the ability to progressively command 2 Hyper-Sonic™ Nozzles independently of one another. This sophisticated dual stage injection management yields the highest increases in HP and cooling along all stages of the engine allowing you to greatly increase the boost & timing of your vehicle safely.

Easy Installation

The settings on OLED control unit can be made within a few seconds without any prior knowledge. The only thing you need to determine is at what boost pressure the injection is to begin and what the maximum boost pressure is. – The variable injection of the Boost Cooler is performed within these two preset boost pressure points. By using the optionally Dual Stage Technology, you´re able to set a 2nd nozzle mapping for optimized injection quantity especially at higher engine load states.

Boost Cooler Stage 2 Power-MAX – Perfect for nearly all turbocharged engines

For positive displacement superchargers (Eaton, Twin Screw) and small fast spooling turbos see (e.g. K03/K04 turbochargers) use the Boost Cooler Stage 2 MAF or our Stage 3 kits for best performance.

Stage 2 POWER-MAX™ Europe Edition

Die Europe-Edition (display & programming in BAR) is exclusively available only by Snow Performance Europe and its European authorized dealers.

Features :

• Boost referenced injection control
  For use with all centrifugal superchargers (ProCharger, Vortech) and large turbos (*)
• Complete with our industry leading 300 PSI UHO pump and Hypersonic Nozzles™
• Dual Stage Technology
  2 nozzle control independently of one another
  (Optional, Upgrade Art.No.: SP10350 required)
• 52mm gauge style progressive water-methanol controller
• Dual tone 7 color OLED screen
• Efficient Intercooling, up to 60°C lower air intake temperature
• Achieve approx. 116-Octan rating, by using ordinary 95-Octan gasoline
• Reduces EGT and oil temperatures
• Allows you to run safely more boost and/or more timing
• Reduces thermical stress on NOS, LPG/Autogas and pre-tuned engines like chiptuning & higher boost levels
• No wear issues, only clean combustion chambers
• No loss of boost as with an intercooler
• Reduces the specific fuel consumption
• Easy installation

Water Methanol Injection at its finest!

Snows most popular kit for low/mid boost engines (<1.7bar) – with Variable Injection (VC-20) and 300PSI/20bar Pumpsystem !

This kit progressively injects more or less water or water/alcohol, according to manifold boost pressure. The system is applicable for turbo/supercharged engines making up to 1.5bar of boost pressure. It has two dials to set the start and full points to tailor the delivery to your engines needs. Progressively injecting according to boost pressure allows for the most power over the widest range of rpms.

Boost Cooler Water injection

Obtain up to 10-25% more power in your turbo- or supercharged engine, even if it´s pre-tuned, by using the Boost Cooler?-Water/Methanol Injection System!

The main function of the Boost Cooler is to suppress detonation caused by high temperature and pressure developed within the combustion chamber when the effective compression ratio has been taken beyond the auto-ignition point by either a turbo or a supercharger.

Water, with its high latent heat content, is extremely effective for controlling not only the onset of detonation but also the production of oxides of nitrogen in the modern lean burn engines.Furthermore, the Boost Cooler doesn’t create an intake restriction like an intercooler, and unlike race gas, it reduces intake air temps up to 60°C and improves charge air density too!

Snow Performance systems effectively steam clean the intake when they inject. This reduces carbon build up. The Boost Cooler? can be installed in a matter of hours without having to remove bumpers or do custom intake piping.

Boost controlled variable injection

This kit uses manifold boost pressure to determine when and how much fluid to inject. Proportionally injecting according to boost pressure gives the most accurate delivery of water-methanol and allows the most cooling and performance improvement over the widest range. More power and driveability is the result! It can be used on any forced induction engine.

The most suitable are the centrifugal supercharged and turbocharged engines, as they build boost is a more progressive manner concerning water-methanol injection. The positive displacement blower engines will work, but it might take more work to dial in the delivery. New: You can switch to a 0-5 Volt output signal from the Mass Air for injection controlling.

Kit includes:

• UHO (Ultra High Output) Pump
• 3 Quart Reservoir
• Digital Variable Controller
• 2 Nozzles To Cover a Wide Range of Horsepower
• All Required Hardware Needed For Installation
• Comprehensive Instructions

Features:

• VC-20 control unit, Boost/MAP controlled, variable injection
• Efficient Intercooling, up to 60°C lower air intake temperature
• Achieve approx. 116-Octan rating, by using ordinary 95-Octan gasoline
• Reduces EGT and oil temperatures
• Allows you to run safely more boost and/or more timing
• Reduces thermical stress on NOS, LPG/Autogas and pre-tuned engines like chiptuning & higher boost levels
• No wear issues, only clean combustion chambers
• No loss of boost as with an intercooler
• Reduces the specific fuel consumption
• Easy installation

Water Methanol Injection at its finest!

The gasoline Stage 1 Boost Cooler™ kit is available for forced induction applications that are either fuel injected or carbureted. Operation is very simple: the system starts injecting when the boost switch reaches the user-adjustable point and it injects a fixed amount of fluid through the nozzle until the switch opens again. This makes it a good choice for low boost setups looking for an octane enhancement and cooler intake charge. Activation can also be set up through any other user-chosen switch, such as a full throttle switch, etc.

Boost Cooler Waterinjection

Obtain up to 10-25% more power in your turbo- or supercharged engine, even if it´s pre-tuned, by using the Boost Cooler?-Water/Methanol Injection System!

The main function of the Boost Cooler is to suppress detonation caused by high temperature and pressure developed within the combustion chamber when the effective compression ratio has been taken beyond the auto-ignition point by either a turbo or a supercharger. Water, with its high latent heat content, is extremely effective for controlling not only the onset of detonation but also the production of oxides of nitrogen in the modern leanburn engines.

Furthermore, the Boost Cooler doesn’t create an intake restriction like an intercooler, and unlike race gas, it reduces intake air temps up to 60°C and improves charge air density too!

Snow Performance systems effectively steam clean intake when they inject. This reduces carbon build up. The Boost Cooler? can be installed in a matter of hours without having to remove bumpers or do custom intake piping.

Kit includes:

• UHO (Ultra High Output) Pump
• 3 Quart Reservoir
• 2 Nozzles To Cover a Wide Range of Horsepower
• Required Hardware Needed For Installation
• Comprehensive Instructions

Note: Safe Injection can not be used with Stage 1 Gasoline Systems

This is a rear counterweight to fit the 13bt found in the RX-7 FC3s Turbo II

These counterweights are required if you are installing an aftermarket lightweight flywheel such as our Racing Beat lightweight flywheel or an uprated clutch/flywheel kit.

Make sure your order one of these with your new flywheel or it cannot be fitted.

Please note that this item is compatible with the 13bt engine found in RX-7 FC3s Turbo II if your using the 13bt Engine in another vehicle this is still the counterweight you will require.
This Counterweight will not be suitable for your RX-7 FC3s EGI engine due to the difference in weight

PLEASE REMEMBER THIS ITEM IS FOR COLLECTION ONLY

High battery made by Varta, to fit the following models.

> Mazda RX-7 FC3s
> Mazda RX-7 FD3s

> Mazda Rx-8

Battery Performance Data
> Voltage – 12 volts
> Capacity – 60Ah
> Cold Cranking Amps – 540CCA

Varta Batteries are made in the same factory as the popular Bosch battery. to the same specification.

This Varta batteries delivery of high CCA means it delivers adequate cranking power to start your car on even the coldest temperatures.

These Varta batteries are great quality and have been used on Essex Rotary cars without fail for many years. Please Select your preference from the drop down below.

FOR COLLECTION ONLY, DUE TO THE FACT THESE BATTERIES ARE LEAD ACID FILLED AND HAVE SEVERE COURIER RESTRICTIONS.

Bosch 1680cc fuel injectors are extremely popular among many of the big power RX-7′s however what is usually overlooked are the soft white/yellowish injector ‘O’ ring found on the top of your Bosch injectors.
These soft ‘O’ Rings are not designed for petrol (they are actually for natural gas) this means that its very common for these seals to start to leak once your fuel rail is pressurized. This can cause the possibility of engine fire one that fuel gets hot enough.
These Injector ‘O’Ring pack contains 4 high quality fuel proof injector seals enabling you to replace the top seals on up to 4 injectors.

Please note these ‘O’ rings have an approximate outer diameter of 14mm and are designed to fit injector of the Bosch 1680 style pictures above. These injectors are commonly installed in many aftermarket fuel rails like those sold by KGParts.

Commonly the most overlooked component in a fuel system, filter neglect can be the most costly. If not cleaned or replaced regularly, filter elements can become clogged resulting in reduced fuel flow, engine performance and ultimately, fuel pump or even worse, engine damage. By simply replacing and/or cleaning your filter elements regularly, you can avoid costly repairs to your fuel system and ensure peak engine performance.

Aeromotive recommends annual inspection and service of filter elements. This includes replacing 10-micron fabric elements and cleaning or replacing 100-micron stainless steel elements. Severe duty applications or newly installed systems may require more frequent maintenance.

How do you know what element you need for your filter? Several Aeromotive filters share the same housing, but the elements inside may be drastically different and putting the wrong filter or element in the wrong place could be costly for your fuel pump or your engine. To find out, look inside the inlet of the filter. Stamped on the top of the element is the micron rating. This will tell you what element you need for your filter.

For Filter P/N’s:

12301
12306
12351
12321

An inexpensive insurance policy to protect your investment, proper filtration is key to fuel system performance. Engineered filter solutions are required to achieve protection with minimum restriction. For 200 – 3,000 plus HP applications, our filter assemblies offer unmatched flow, ease of installation and maintenance, along with the impeccable machining and finish you’ve come to expect from all Aeromotive components.

• High-flow, 10-micron fabric (fine) replaceable element.
• Flows 2,000 lb/hr with a pressure drop of less than 1 PSI.
• Compact size: 5.5′ long x 2′ diameter
• All filter assemblies feature an O-ring for positive sealing in high pressure applications.
• CNC-machined from 6061-T6 aircraft aluminum.
• Bright dip red anodized finish for a corrosion resistant, show car quality appearance.

10-micron filters may ONLY be used after the fuel pump to protect your injectors or carburetor.
Fabric elements not suitable for use in E85 or alcohol applications.

A great solution for getting a high quality filter element in to your performance fuel system.

This high quality liquid filled gauge is the ideal companion for your inline fuel rail adapter or A1000 Fuel Pressure Regulator.
Enabling you to accurately check and set fuel pressure.

• Fuel Pressure Gauge• 1.5” Diameter
• 0-100 PSI
• Liquid Filled
• Includes integral pressure relief valve.

The Ideal Companion for your Aeromotive A1000 Fuel Pressure Regulator.

Performance EFI regulator designed for medium to high horsepower applications. This regulators features Aeromotive’s high-flow design, superb pressure control and legendary durability. On the street and at the track, this pressure regulator has logged more miles, laps and passes than any other performance EFI regulator in the world!

•  Base pressure adjustable from 40-75 PSI.
•  Gasoline and alcohol compatible.
• Fuel pressure rises on a 1:1 ratio with boost.
•  1/8” NPT gauge port.
• ORB-06 Inlet and Outlet Ports

Popular with modified RX-7′s this regulator can be used on your RX-8 however it would require conversion to a return fuel system.

Carbon Kevlar Bucket Seat from SEIBON

Seibon Carbon components are carefully hand-crafted using only the finest materials. Our production team offers superior craftsmanship with over 15 years of experience working with carbon fibre.

SEIBON parts are special order only so please contact us for estimated delivery times if your in a hurry for your part. Due to the nature of these products being hand made we are unable to offer a guarenteed estimated lead time for delivery once your order is placed.

Save on a 12 bottle pack plus combined Shipping. Save over £35.00 on this pack, This pack works out at £11.00 per bottle.

Possibly The Best Rotary Premix You Can Buy

Inherently with many rotary engines, the entirety of the rotor and housing are not being sufficiently lubricated, resulting in premature wear or damage. In order to increase lubrication within the rotary, Idemitsu developed Idemitsu Rotary Premix.  At 1/2 oz per gallon of fuel, it is a cost effective way lubricate more of your engine and prevent premature catastrophic damage.

• A special blend of base oils reduces deposits and subsequent exhaust port clogging. As a result, your rotary will maintain the power at which it was designed.
• Special detergent/dispersant additives keep you fuel injectors clean to reduce maintenance.
• Provides additional lubrication for apex and side seals to increase seal life and increase efficiency of engine.
• Special additives allow for better sealing of the chamber, creating greater efficiency and more power.
• Idemitsu Lubricants America Corporation recommends the use of the Ratio Rite Measuring cup to ensure a proper mixture of Premix Rotary Fuel Lube and gasoline.

A full synthetic oil specially formulated for your rotary engine from Idemitdu Each Bottle contains 1 US Quart of Oil

Save on a 6 bottle pack plus combined Shipping. Save £11.94.00 on this pack, This pack works out at £12.00 per bottle

Possibly The Best Rotary Premix You Can Buy

Inherently with many rotary engines, the entirety of the rotor and housing are not being sufficiently lubricated, resulting in premature wear or damage. In order to increase lubrication within the rotary, Idemitsu developed Idemitsu Rotary Premix.  At 1/2 oz per gallon of fuel, it is a cost effective way lubricate more of your engine and prevent premature catastrophic damage.

• A special blend of base oils reduces deposits and subsequent exhaust port clogging. As a result, your rotary will maintain the power at which it was designed.
• Special detergent/dispersant additives keep you fuel injectors clean to reduce maintenance.
• Provides additional lubrication for apex and side seals to increase seal life and increase efficiency of engine.
• Special additives allow for better sealing of the chamber, creating greater efficiency and more power.
• Idemitsu Lubricants America Corporation recommends the use of the Ratio Rite Measuring cup to ensure a proper mixture of Premix Rotary Fuel Lube and gasoline.

A full synthetic oil specially formulated for your rotary engine from Idemitdu Each Bottle contains 1 US Quart of Oil

Quality replacement fuel filter for your RX-7 FC3s

A high quality clutch release bearing for push type clutches found on the RX-8 and RX-7 FB and FC3s

It is highly recommended that this bearing is replaced at any opportunity  due to the considerable labor involved if it fails.

Please note that this will not fit the FD3s clutch if it has not been converted from pull type clutch mechanism to push type.

This part can also be referred to as a Throw Out Bearing or Thrust Bearing.

Image for Illustration Purposes Only, Actual Bearing may differ from that show.

Race Proven Gearbox Oil from Idemitsu

This formulation has been specifically engineered to provide maximum performance and protection for engines under severe racing conditions. Built on a tradition of excellence by IDEMITSU, this technology is derived from decades of experience formulating premium lubricants for Japanese auto manufacturers.

• Formulated Specifically For High Performance Gearboxes

• Enhanced Film Strength Provides Excellent Durability and Wear Protection

• Advanced Extreme Pressure Additive Package Improves Performance Under High Load Conditions

• Superior Shear Stability Ensures Viscosity Retention Under High Stress Operations

• Provides Smooth Shifting Across All RPMs

Each bottle contains 1 US quart of oil, please note you will require the following amounts for each kind of gearbox

3 Bottles for RX-8 5 Speed Gearbox and RX-7 FD Gearbox

Possibly The Best Rotary Premix You Can Buy

Inherently with many rotary engines, the entirety of the rotor and housing are not being sufficiently lubricated, resulting in premature wear or damage. In order to increase lubrication within the rotary, Idemitsu developed Idemitsu Rotary Premix.  At 1/2 oz per gallon of fuel, it is a cost effective way lubricate more of your engine and prevent premature catastrophic damage.

• A special blend of base oils reduces deposits and subsequent exhaust port clogging. As a result, your rotary will maintain the power at which it was designed.
• Special detergent/dispersant additives keep you fuel injectors clean to reduce maintenance.
• Provides additional lubrication for apex and side seals to increase seal life and increase efficiency of engine.
• Special additives allow for better sealing of the chamber, creating greater efficiency and more power.
• Idemitsu Lubricants America Corporation recommends the use of the Ratio Rite Measuring cup to ensure a proper mixture of Premix Rotary Fuel Lube and gasoline.

A full synthetic oil specially formulated for your rotary engine from Idemitdu Each Bottle contains 1 US Quart of Oil

Pack discounts for 6 bottle packs and 12 bottle packs can be purchased via our Idemitsu Shop

A Full Synthetic Oil SAFE for your Rotary Engine

Do you feel that you aren’t getting the power you should be from your rotary engine? Are you experiencing bearing wear under severe (or possibly under not-so-severe) operating conditions? If so, you may be using the wrong engine oil. Idemitsu 20W-50 can reduce or even eliminate some of the problems you may be having. As the developer of the engine oil for the winning 1991 LeMans Mazda 787B and a long time supplier of vital lubricants to Mazda, Idemitsu has intimate knowledge of the requirements of rotary engines.

• With the precise base oil mix of PolyAlphaOlephins and PolyEsters, Idemitsu Rotary Engine Oils are able to minimize those deposits on your apex seals. 
• Allows for better sealing of the chamber, facilitating more power generation. 
• Extends the life of turbochargers by reducing bearing coking.
• Specially developed additives facilitate even tooth load on the front stationary gear to allow for higher loads and higher RPM.
• Premium anti-wear agents create a strong film between the main bearings and the eccentric shaft, reducing metal-to-metal contact and minimizing bearing wear.
• Developed to reduce entrained gas generation. Entrained gases reduce the oils ability to prevent metal-on-metal contact, thereby increasing main bearing wear.
• Includes Molybdenum as a friction modifier. This compound reacts with the metal surfaces to create a low-shear boundary. The low shear characteristic reduces friction, increasing efficiency and power output. 

A full synthetic oil specially formulated for your rotary engine from Idemitdu Each Bottle contains 1 US Quart of Oil  

A Full Synthetic Oil SAFE for your Rotary Engine

Do you feel that you aren’t getting the power you should be from your rotary engine? Are you experiencing bearing wear under severe (or possibly under not-so-severe) operating conditions? If so, you may be using the wrong engine oil. Idemitsu 10W-30 can reduce or even eliminate some of the problems you may be having.

As the developer of the engine oil for the winning 1991 LeMans Mazda 787B and a long time supplier of vital lubricants to Mazda, Idemitsu has intimate knowledge of the requirements of rotary engines.

• With the precise base oil mix of PolyAlphaOlephins and PolyEsters, Idemitsu Rotary Engine Oils are able to minimize those deposits on your apex seals. 
• Allows for better sealing of the chamber, facilitating more power generation. 
• Extends the life of turbochargers by reducing bearing coking.
• Specially developed additives facilitate even tooth load on the front stationary gear to allow for higher loads and higher RPM.
• Premium anti-wear agents create a strong film between the main bearings and the eccentric shaft, reducing metal-to-metal contact and minimizing bearing wear.
• Developed to reduce entrained gas generation. Entrained gases reduce the oils ability to prevent metal-on-metal contact, thereby increasing main bearing wear.
• Includes Molybdenum as a friction modifier. This compound reacts with the metal surfaces to create a low-shear boundary. The low shear characteristic reduces friction, increasing efficiency and power output. 

A full synthetic oil specially formulated for your rotary engine from Idemitdu

Each Bottle contains 1 US Quart of Oil